All Airsoft Batteries

This battery features a wider and flatter butterfly style configuration and while it won't fit in crane stocks it is perfect for larger areas such as AR36 handguards and full stock rifles. The battery has a voltage of 7.4v, a capacity of 1500mAh and a continuous discharge rate of 20C with a maximum discharge rate of 40C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with a Deans connector, however adaptors are available.

The battery consists of two cells working in tandem with each other, with each cell measuring 8.5x0.6x3.4cm with a cable length of roughly 9cm.

If you need an Airsoft battery that fits in almost anything and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo/ LiFe/NiMH Balance Charger, a Safe Charging Bag and an ASG 7.4V 1300mAh LiPo Battery in Crane configuration with a Mini-Tamiya connector; an ideal setup for Mini-Tamiya equipped AEGs and capable of fitting inside Crane stocks, fixed stocks and most handguards! If you have multiple different AEGs and you want a battery to fit them all, chances are this one will! 

The dimensions of the included battery are as follows: 10.1cm x 0.7cm x 2cm per cell group (2x cell groups on each battery) with approximately 10cm of wiring between the battery and connector. 

Compatible with: M4/AR-15 Crane Stock, M4/AR-15, SMG-5 & AK Fixed stock, AR-36 & SMG-5 handguards, Tokyo Marui SCAR-L/H NGRS stock, most M4/AR-15 buffer tubes. 

If you are heavy on the trigger with your LiPo ready AEP you might need a couple of these! The IPower 7.4V 680mAh 20c LiPo battery is just like a normal LiPo stick, but much much smaller. This battery is designed as a spare battery for the CYMA CM.xxxS series of LiPo-ready AEPs and is pre-wired to a mini-Deans connector. This battery can be charged like a normal LiPo battery; using the balance lead and with a LiPo balance charger. This battery cannot be charged with a normal NiMh/NiCad charger, do not attempt it as you may cause a fire. If you are the creative type this battery's minuscule form could lend itself well to an electronics project or R/C use.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too, and is designed to give you a high output for fast rate of fire and trigger response for roughly half a day dependent on trigger happiness.

An 11.1v 1200mAh 20c LiPo Battery with a Deans Connector in a Stick configuration, making it ideal for Solid Stocks and some rear wired Buffer Tubes. It has the following dimensions with a 9cm cable: 2cm x 1.63cm x 13cm.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards  and comes fitted with Deans connectors instead of the standard Tamiya for upgraded Airsoft Guns.

An 11.1v 1300mAh 20c LiPo Battery with a Deans Connector in a Stick configuration, making it ideal for Solid Stocks and some rear wired Buffer Tubes. It has the following dimensions with a 9cm cable: 2cm x 1.62cm x 12.8cm.

A high powered Airsoft Battery, designed to be used in highly tuned top-end gearbox. The battery comes in a 'stick' configuration, with two adjoined cells in one block, allowing the battery to be squeezed into even the tightest of buffer tubes. 

A triple crane stock 11.1v 1450mAh 25C LiPo, which features a Deans connector instead of the standard small Tamiya.

This is a high quality NUPROL 8.4v 1600mAh NiMH stick battery often used within Airsoft AK AEGs, or other weapons that features a long, thin battery compartment.

Suitable not only for Airsoft but for RC vehicles and toys too. This Stick Battery is relatively large and excellent for ensuring you get a full day's play out of one charge, providing you're not too trigger happy.

If you need a compact Airsoft battery which fits almost anywhere the 7.4v 1100mAh 20C LiPo Crane Battery from VAPEX is ideal. This battery is pre-wired with a mini-Tamiya battery connector and each cell unit measures 11 x 0.7 x 2.2 cm with approximately 9 cm of wiring between each cell and the connector, making it great for tight spaces and use with multiple different platforms.

The compact size of this crane/nunchuck battery makes it ideal not only for Airsoft but also for electronics hobby applications and R/C when a lightweight and compact power source is a priority. Whether it needs to fit into a buffer tube, crane stock, handguard or practically anywhere else this super slim battery is perfect, especially if you want a single battery which fits in multiple guns!

An individual 3V Lithium Button Battery, which are commonly used in Airsoft Sights, Scopes and other Accessories. 

A LiPo crane stock battery designed to fit in crane and solid stocks, where other batteries would be wasting the available space. 

Proven in battle, everyone has use for Ni-Mh crane stock batteries! The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance so you can use any charger as long as it's NiMh compatible, just make sure to not leave the battery charging unattended.

This battery has a voltage of 9.6v and a capacity of 1600mAh and is comprised of 8 cells working in unison, connected via the Deans/T-Plug connector.

This Ni-Mh sports a crane configuration, one of the most common types and is perfect for split battery compartments, most often seen in M4 stocks, M16, SMG-5 and AKs with full stocks. The battery measures 12x1.8x1.8cm per 4x cells and has a wire length of roughly 8cm.

If you are looking for a decently sized crane stock battery which should last all day, the VAPEX 7.4v 2200mAh 20C LiPo Crane Battery should do the trick! This battery is a 7.4V 2S LiPo in crane/nunchuck configuration, meaning the cells are separated into two individual units which makes the battery far easier to fit into unconventionally shaped battery compartments. The pre-wired connector is the common mini-Tamiya connector and the continuous discharge rate is 20C.

Each of the individual cell units measures 11x2.2x1.2cm approximately with a wire length of 9cm between each cell and the connector, meaning this should fit nicely in most crane stocks and many handguards and full-stock battery compartments, though as always, we advise measuring carefully before ordering!

A 9.6v 1600mAh NiMh battery in stick configuration, often used within Airsoft AK AEGs. With a slow charge you can expect up to a whole day of Airsoft action from one charge.

An ultra-thin and lightweight battery, perfect for squeezing into even the tightest spots. The battery provides 1200mAh of power with a discharge rate of 20c. The battery is so thin it can fit into stock tubes and AK/MP5 AEG Battery compartments.

If you need a battery to fit into a tight place, Evolution Airsoft have you covered with the 7.4V 1100mAh 20C LiPo Stick Battery. This battery comes pre-wired with a Deans battery connector, also known as a "T-Plug" but is packaged with a Deans to mini-Tamiya adapter, meaning it can be used with almost any Airsoft AEG around.

The battery is a 2 cell 7.4V LiPo battery in stick configuration, meaning the cells are bound together into a single unit. The wire length between the battery and connector is approximately 10cm, the continuous discharge rate is 20C and the peak discharge rate is 40C. Whether you need a battery for your Airsoft gun or another electronics hobby which requires a compact power source, this Evolution Airsoft battery will do the trick!

A high powered Airsoft Battery, designed to be used in highly tuned top-end gearbox. 

A compact yet high output LiPo battery designed for most M4 stock tubes, solid stocks and some hand guards.

Popular VP Racing 8.4v 1600mAh stick battery often used within Airsoft AK AEGs, or other weapons that features a long, thin battery compartment.

An 11.1v crane stock LiPo Battery with an impressive 2600mAh capacity, designed to ensure that your Airsoft AEG can survive a whole day of Skirmishing.

A LiPo crane stock battery designed to fit in stocks and small spaces which other large batteries do not fit.

A 23cm long 9.6v NiMH stick battery, ideally suited for powering top wired AEGs such as the AK47 and other weapons with a long and thin battery compartment.

A high quality and compact PEQ box sized 11.1v Lithium Polymer Battery with 1300mAh of capacity, and a 20C discharge rating

An absolutely massive 11.1v LiPo 2600mAh 20c LiPo Battery in a Crane Stock configuration, with three cells which have individual dimensions of: 13.1cm x 1.98cm x 1.13cm. It has a 9cm cable with a Deans Connector on the end.

If you need a compact block battery for a handguard or fixed stock with limited space this should do the trick! The 7.4V 1500mAh 20C LiPo Block Battery from Electro River measures 8.5 x 1.2 x 3.4cm approximately with a wire length between the cell group and connector of approximately 9cm.

The pre-wired connector is the Deans/T-plug the continuous discharge rate is 20C and the maximum is 40C, making this battery great for both Airsoft applications and electronics hobbies.

If you're looking for a tiny LiPo battery for your Novritsch SSE18 or CYMA CM.1xxS MOSFET equipped AEP, this is what you need. The Novritsch 7.4V 600mAh LiPo Battery measures approximately 7.3 x 1.5 x 1cm and is pre-wired with a Mini-Deans battery connector and a 3 port balance connector. 

As with other LiPo batteries, this battery should only ever be charged on a LiPo balance charger, preferably in a battery charging bag and should not be left on charge unattended under any circumstance.

If you are looking for the biggest battery you can fit in an M4/AR-15 buffer tube this would be it! The 7.4v 2000mAh 15C LiPo Stick Battery from Electro River just about fits in an M4/AR-15 buffer tube, though we recommend you do not fully collapse the stock once it is installed.

The battery measures 12.6 x1.6 x 2cm and should also be suitable for top-wired AK AEGs and will fit in almost all fixed stock battery compartments regardless of the platform. The wire length between the connector and cell group is approximately 9cm and the continuous discharge rate is 15C with a peak discharge rate of 30C.