Gate TITAN Drop In MOSFET V3 Advanced Firmware Complete Set

The board is specially coated with Mil-Spec MIL-V-173C Varnish, making it moisture and fungus resistant, and supports batteries in the range of 3V up to 17v, making it great for Ni-Mh, Ni-Cd, Li-Po, and Li-Fe Batteries and is compatible with most V3 Gearbox on the market with no modification. The Titan Board itself is built in the EU by Gate Electronics, and comes with a 12 Months Manufacturer Warranty for defects and stands out from the crowd due to its Optical Sensor Controlled System rather than Mechanical ,and has Eight Onboard Optical Sensors. The board boasts a huge array of features, with the most impressive being the Auto-Adjusting pre-cocking and breaking system, using the on-board sensors to detect the position of the Gearbox's Gear's Teeth, allowing the system to get a perfect result with almost no configuration. The board itself, once installed, is capable of very fast repeated semi-shots, with gearbox protection ignoring the trigger pull if the rifle is not ready, allowing for faster, more consistent shots compared to other units. Once installed the included MOSFET unit can be re-programmed via the Gate Configuration Card or via the USB-Link to a PC, Laptop, and even Mobile Phones, allowing the firmware to be updated, and can be used to Error Check your Weapon should something go wrong. Whats important to highlight with the Titan, is that its strength lies not just in its list of features, but also in how well they've been implemented. For more information on this Gate MOSFET, please see the extensive list of features in the Features Section. Should you need any help installing the MOSFET please feel free to call our workshop on: 01484 644709.

Features

• Name Designation: TITAN Drop In MOSFET V3 Advanced Firmware Complete Set
• Manufacturer: GATE Electronics
• MPN: TTN-CR
• Construction: Mil-Spec MIL-V-173C Coated (Moisture and Fungus Resistant)
• Compatibility: Standard Airsoft V3 Gearbox AEG without Existing MOSFET
• Battery Support:
  • 8.4v Ni-Mh
  • 7.4v LiPo
  • 9.6v Ni-Mh
  • 11.1v LiPo
  • 12.8v LiFe
  • 14.8v LiPo
• Operating Ranges: 3v - 17V
• User Guide: 
  • Assembly and Calibration Manual
  • Tactical Programming Card Manual
  • USB-Link Manual
  • Gate Control Station v0.9 Beta Manual
• Downloads:
  • Gate Control Station

Features

• Built in the EU
• Complete TITAN Kit, with Programming Card and USB-Link Included
• Version 3 Edition Board, for V3 Gearbox
• 12 Months Manufacturer Warranty
• Complete Trigger Set replacement Kit
• Designed for Highly Efficient V3 AEG Builds
• Suitable for Stock Guns and Upgraded Guns
• Great for DMR and Standard Setups
• Reprogrammable with a the Titan Programming Card and USB Link
• Optical Sensor Controlled
• Advanced Optical Sensors for the Trigger, Gears and Selector
• Compatible with most V3 Gearbox on the market without Modification
• Auto-Adjusting Precocking / Braking system
• Works with Dual Sector Gear and Short Stroked Gears
• Detects up to 6 Trigger Positions for the Fine Tuning of the Trigger Breakpoint
• Capable of Fast Repeat Shooting
• MILSPEC Board coating
• Adjustable Trigger Sensitivity
• Adjustable Pre-cocking Boost
• Adjustable Fire-Selector Mode
• Adjustable Burst Mode
• Adjustable Rate of Fire
• Two-Stage Trigger Mode, Possible for Semi / Full Auto without using a Fire Selector
• Sniper Delay Modes
• Run-away Motor 30 Rounds Limit Mode
• Protection for the Titan Unit against Over Current, Under Current, and Overheating 
• Low Battery Warning
• Over-discharge Battery Protection
• Configurable Fire Selector
  • Safe - Semi - Auto
  • Safe - Semi - Semi
  • Safe - Semi - Burst
  • Safe - Burst - Auto
  • Safe - Semi - Burst / Auto (Short Press - Burst, Long Press - Auto)
  • Semi - Burst - Auto (Safe Mode via fast switch Safe - Semi - Safe)
• Kit comes with required parts for Fitting (Please see Special Instructions)
• Deans Connector Type
• Protection for Li-Po, Li-Ion, Li-Fe, Ni-Cd Batteries
• Optical Sensor Test Mode for easier Installation
• Updatable Firmware via USB-Link on a Windows / MAC PC
• Statistics and Additional Settings Accessible using a USB-Link with GATE-CS
• Can be Diagnosed for Errors using the Programming Card or USB-Link
  • UVP1 – your battery is discharged
  • UVP2 – the voltage is lower than 3.8V
  • OCP1 – overcurrent protection
  • OCP2 – the motor power supply circuit is shorted
  • OTP – the drop-in module temperature is too high
  • MOTOR DISC – you pulled the trigger but the motor did not move
• Smart Fuse System

Package Includes

• TITAN Drop In MOSFET V3 Advanced Firmware Complete Set
• USB-Link
• USB Cable x3
• Quickstart Guides
  • 'USB-Link'
  • 'Firmware Editions Guide'
  • 'Titan Drop-In Module'
• Installation Kit
  • Deans Connector Set (Gun End)
  • rigger Anti-Blacklash Sticker (0.5mm) x3
  • Trigger Anti-Blacklash Sticker (0.3mm) x3
  • Trigger Anti-Blacklash Sticker (0.15mm) x3
  • Washer (0.3mm) x2
  • Washer (0.2mm) x2
  • Washer (0.3mm) x1

Special Instructions:

Please note, this box contains the TITAN Tactical Programming Card and USB-Link, everything you need to build and install the TITAN MOSFET.

Please only use either the Tactical Programming Card, or the USB-Link at any one time. Do NOT connect them both at the same time.

Should you need any help installing the MOSFET please feel free to call our workshop on: 01484 644709.

Please note that the warranty covers the unit from defects, not improper installation. Please read all user guides before installing, for more information please see the supplied Warranty Card.

Please remember when installing the device to ensure your AEG is clear before use.

Ensure that when wiring up the device the Positive and Negative battery terminals are the correct way around as this will cause immediate damage to the unit.

Please note, that battery protection is not compatible with Ni-Mh and Ni-Cd Battery

For warranty related issues please visit: http://gatee.eu/technical-support/warranty

Any claims made under warranty will result in your unit/s being sent back to GATE HQ which may take up to 4 weeks to be resolved after testing. 

The GATE Control Station Software can be downloaded at the following link:

• Gate Control Station