G&G Armament CMF

As this AEG is aimed at indoors players, it is mostly constructed from an incredibly tough and light Polymer, with Alloy strengthening in important places like the Outer Barrel and Buffer Tube. The lightweight nature of the Rifle and high Rate of Fire will make it a welcome choice for those playing outdoors too. Despite being mostly Polymer, the Gun still clocks in at 2.53kg, so it definitely feels like a quality bit of kit in the hands.

The CMF Series have a typical AR layout, with a 14mm CCW Thread hiding underneath the Flash Hider, which can be used to installed Suppressors and Tracer Units once the Flash Hider has been unscrewed. The main point of interest is the M-LOK Railed Handguard which reduces weight by having less unnecessary material. You can either attach M-LOK accessories directly to the rail, or install 20mm Rail Adapters so that you only have Rail where it is needed. There is even a set of QD Sling Sockets on the Handguard, allowing you to install Quick Release Loops for easy Sling Installation/Removal. The top of the Handguard has a 20mm Rail that runs all the way back to the rear of the Receiver, allowing you to easily install Sights and Scopes. This Rail comes with a set of Flip Up Ironsights installed out of the box, which can be left in place to use as a backup, or removed completely. The Ironsights are easily adjustable by hand, so that you will be able to align them with your BB impacts.

The Receiver features almost COMPLETELY Ambidextrous Controls which is a very welcome treat. The Fire Selector, Magazine Release and Bolt Release can all be operated from either side of the Gun, making this very comfortable for both Left and Right Handed players. The Fire Selector can be programmed for Burst Fire instead of Full Auto by holding down the Trigger for 10 seconds whilst the Selector is set to Semi. Repeat this process to reinstate Full Auto. The rear of the Receiver has an Ambidextrous Sling Plate, allowing you to connect a Sling from either side of the Gun, again benefiting both Left and Right Handed players. The Stock of the Gun is a Sliding Crane Stock design which is where your Battery should be installed, and can be slid to one of Six Positions to suit all shapes and sizes of player. To access the Mini Tamiya Connector inside, simply squeeze the tabs at the rear of the Stock and pull away the Rubber Butt Pad. 

Due to the G&G ETU and 4th Gen MOSFET, this Gun will require an 11.1v LiPo with a max discharge rating of 15C to operate at its' best. The Battery Protection on the MOSFET will stop the Gun from firing if the detected Voltage is too low. This means that whilst your 7.4v LiPo might work for the first magazine, as soon as the capacity hits a certain level, the Gun will stop working until a Battery with enough Voltage is detected. The MOSFET is also responsible for the programmable Fire Modes which set this Gun apart from other standard replicas. The package is finished off with the classic G&G Electronic Trigger Unit which yields a much faster Trigger Response than standard, as well as protecting the longevity of the Trigger by removing the need for traditional Trigger Contacts (which would eventually stop working due to Carbon build-up).

Included in the box is a 450rnd High Cap Magazine and the Gun itself. If you're a seasoned player and you're wanting to step up your effectiveness in CQB, or have much better volume of fire for outdoor games, then the G&G Armament CMF will do exactly that.

Features

• AR Platform Replica
• 4th Generation MOSFET
• Electronic Trigger Unit
• 11.1v LiPo Ready
• Programmable Burst Fire
• Lightweight & Tough
• Reinforced Polymer
• Alloy Outer Barrel
• 14mm CCW Thread
• M-LOK Railed Handguard
• QD Sling Sockets
• 20mm Railed Receiver
• Flip Up Ironsights
• Ambidextrous Fire Selector
• Ambidextrous Mag Release
• Ambidextrous Bolt Release
• Ambidextrous Sling Plate
• Six Position Sliding Crane Stock
• Rear Wired / Mini Tamiya
• 450rnd High Cap Magazine
• Ideal CQB Airsoft Gun
• Two Versions Available
• Rubber Butt Pad

Package Includes

• G&G Armament CMF
• 450rnd High Cap Magazine
• QD Sling Loop (16K variant only)

Special Instructions

Please note that the manufacturer recommends the use of an 11.1v LiPo Battery with a maximum discharge rating of 15C to safely operate the Gun and stay within warranty. The battery compartment on the G&G CMF 16K is very small, we recommend a small stick battery for this AEG. The following are examples of compatible batteries:

ASG 11.1V 900 mAh LiPo Stick Battery

Specna Arms 11.1V 600mAh LiPo Stick Battery

To Program Burst Fire:

1. Install a Battery in the Gun
2. Ensure the Gun is EMPTY or pointed in safe direction
3. Set Fire Selector to 'Semi'
4. Hold Trigger for ten seconds
5. Full Auto will now be 3rnd Burst

Repeat these steps to reset the Full Auto function

Please note that only the 16K Variant is supplied with a Quick Release Sling Loop.