Airsoft Rails

If you want to save some weight on your AR36 or Novritsch SSR63 and give it a whole new look, you have found what you need! The Novritsch Minimal 20mm Picatinny Rail Kit for SSR63/AR36 AEG is constructed from alloy with steel mounting bolts and is compatible with the full range of Novritsch SSR63 AEGs as well as most AR36 AEG and GBBR platforms. The part is manufactured by Double Bell, includes built-in flip-up iron sights and is based on the real steel KAC design. 

The set provides a 20mm Picatinny top rail measuring approximately 10cm in length, enough for most red dot sights and smaller magnified scopes while minimising excess material to keep the weight low. The built-in flip-up iron sights are fully adjustable, with a single rear aperture which can be raised and lowered by turning the drum just below the aperture and adjusted left and right via the drum on the right side. If your AR36 needs a style up or you want to lean in to the light and tight design philosophy of the Novritsch SSR63, this kit is the perfect upgrade!

The Delta Armory 22mm Offset Angled Mount has an aluminium alloy construction, making it tough and lightweight. It is designed to install Torches, Lasers and other 20mm RIS Accessories at a 45-degree angle, which allows you to maximise the available space you have on your Airsoft Gun.

An advantage of this mounting method is that it makes your device easier to reach and use, as well as limiting obstruction to other accessories. Although designed for torches, this rail could also be used to mount an offset Red Dot Sight to use as a backup to your main sight. The Delta Armory 22mm Offset Angled Mount easily attaches to 20mm Rails via the Allen Screw on the side of the unit.

With the Novritsch SSX23 Frame Rail, you can mount a flashlight or runcam on the underside of your barrel. It is constructed from strong, lightweight aluminium and is attached to the SSX23 barrel via 2 mounting screws. To attach the frame rail you are required to remove the slide, and then drill two holes at the front under the barrel, where the indents are. After this, you can screw the frame rail in and you're good to go!

The Novritsch SSX23 Frame Rail is a game changer if you skirmish in dark CQB arenas and need the flashlight to stay ahead of the opponents. Instead, this rail section can house a zoom/runcam to capture any long-range or clutch BB shots so you can brag to everyone that you are the ultimate Aisoft extraordinaire!

If you're rocking the super-slick FABARM STF 12 Short Initial and want to top it off with an optic, this is what you need! The BO Dynamics 20mm Picatinny Top Rail for FABARM STF 12 Gas Shotguns is designed to mount to the receiver of your STF 12 via its innovative quick detach mechanism, offering a full-length 20mm Picatinny rail and light-enhancing front and rear iron sights. The front sight insert is red and the rear is green, guaranteeing you'll never mix them up in the heat of a firefight!

The rail itself is constructed from CNC machined aluminium and the iron sights are removable if you prefer to run a red dot sight. This rail fits both gas variants of the STF 12 and is ideal for the Short Initial as it doesn't include a top rail. If you've taken a tumble with your Compact variant, this rail makes a great replacement part if you simply cannot live with scratches! 

The VSR/Bar-10 is still an absurdly popular rifle today, only one problem - No bottom RIS rail! Fear not Laylax have just the thing, a 20mm RIS rail that fits over your front Harris lug. Measuring roughly 9.5cm and just under 4 inches, the rail allows you to attach some much needed tactical equipment to your VSR, such as a bipod for additional sniping stability.

Constructed from tough, but lightweight aluminium, the rail is screws in place to the underside of the fore stock. It also comes with a magazine catch so you can still reload as you normally would. Treat yourself and your VSR to some additional tactical upgrades with a rail mount!

If you have a MK23 NBB pistol you might have noticed the lack of options for mounting accessories. At one point in time the MK23 was cutting edge, but in the current day and age it is in dire need of a Picatinny rail to mount some tactical goodies. Enter the Hades Airsoft MK23 rail adapter, the answer to your prayers!

If you want to add a modern touch to your AK, the CYMA Aluminium KeyMod Handguard for AK-47/74 is what you need! This CNC Aluminium handguard is equipped with KeyMod negative space attachment slots at 3, 6, & 9 o'clock with a 20mm Picatinny rail running along the top, ready for a PMC-style forward-mounted red dot sight. 

On each side, we are treated to a pre-installed 20mm Picatinny rail adapter for KeyMod, giving you the option of using more common 20mm Picatinny accessories or removing the adapters to mount more modern KeyMod solutions. The handguard itself is constructed in two parts, allowing you to use both or simply the upper or lower handguard, depending on your build requirements. If you're going for the modern tactical AK look, the CYMA Aluminium KeyMod Handguard for AK-47/74 is perfect for your build!

Adding rails to your AK can be a chore, but users of the superb GHK AK GBBR platform now have one more option! Introducing the 20mm Picatinny Railed Gas Tube for GHK AK GBBR, an aluminium replacement gas tube with a 20mm Picatinny rail built into its upper surface. This rail is great for a forward-mounted optic but has plenty of space for mounting a tactical flashlight and also a PEQ laser if you have your primary sight mounted on a rail further back. If you are looking for a simple way to give your GHK AK GBBR a hint of modernity, this is the perfect piece!

If you're building out your AK to match the latest real steel builds, the 5KU 20mm Picatinny Rail Mount for Zco AK handguard is essential. Based on real steel Zco-style red dot risers, this aluminium component fits replica Zco-style handguards such as the 5KU Lightweight Zco-style Lower Handguard. It will only attach to these styles of handguards due to the unique attachment interface.

Atop the riser is a section of 20mm Picatinny rail, perfect for mounting a red dot that matches the modern Russian design. If your modern Zco-style AK requires optic space for longer-range engagements, the 5KU 20mm Picatinny Rail Mount for Zco AK handguard is the piece of equipment for you.

If you're looking for a rail riser for a clearer view down your optic, the PTS Syndicate Unity Tactical FAST 20mm Picatinny Optic Riser; Polymer Version should suit your needs perfectly. This riser is based on the real steel Unity Tactical FAST riser, designed to provide a more natural neck position for improved comfort and faster target acquisition, especially for full-face mask and respirator users. 

Being constructed from high-density polymer makes this version of the PTS Unity Riser around half the price of the original aluminium version while offering the same performance as it pertains to Airsoft. If you're seeking a riser and want something a little more tacticool, the PTS Syndicate Unity Tactical FAST 20mm Picatinny Optic Riser; Polymer Version is exactly that!

If you're looking for a rail riser for a clearer view down your optic, the PTS Syndicate Unity Tactical FAST 20mm Picatinny Optic Riser; Polymer Version should suit your needs perfectly. This riser is based on the real steel Unity Tactical FAST riser, designed to provide a more natural neck position for improved comfort and faster target acquisition, especially for full-face mask and respirator users. 

Being constructed from high-density polymer makes this version of the PTS Unity Riser around half the price of the original aluminium version while offering the same performance as it pertains to Airsoft. If you're seeking a riser and want something a little more tacticool, the PTS Syndicate Unity Tactical FAST 20mm Picatinny Optic Riser; Polymer Version is exactly that!

If you're looking for a rail riser for a clearer view down your optic, the PTS Syndicate Unity Tactical FAST 20mm Picatinny Optic Riser; Polymer Version should suit your needs perfectly. This riser is based on the real steel Unity Tactical FAST riser, designed to provide a more natural neck position for improved comfort and faster target acquisition, especially for full-face mask and respirator users. 

Being constructed from high-density polymer makes this version of the PTS Unity Riser around half the price of the original aluminium version while offering the same performance as it pertains to Airsoft. If you're seeking a riser and want something a little more tacticool, the PTS Syndicate Unity Tactical FAST 20mm Picatinny Optic Riser; Polymer Version is exactly that!

The PTS Enhanced Rail Section for M-LOK is an Airsoft modular rail panel designed to be fit onto M-LOK hand guards, providing a 20mm RIS / RAS rail for mounting Picatinny accessories such as torches, lasers, grips and many other aftermarket attachments. The rail is available in several different lengths depending on what you require. This rail has a sleek look, owing to the weight-reducing corner cuts, keeping your M-LOK rail looking slick!

This rail is the perfect purchase for any Airsoft player who has got their hands on a new rifle with an M-LOK attachment system and is looking to take their gun to the next level by attaching parts and accessories.

The PTS Enhanced Rail Section for M-LOK is an Airsoft modular rail panel designed to be fit onto M-LOK hand guards, providing a 20mm RIS / RAS rail for mounting Picatinny accessories such as torches, lasers, grips and many other aftermarket attachments. The rail is available in several different lengths depending on what you require. This rail has a sleek look, owing to the weight-reducing corner cuts, keeping your M-LOK rail looking slick!

This rail is the perfect purchase for any Airsoft player who has got their hands on a new rifle with an M-LOK attachment system and is looking to take their gun to the next level by attaching parts and accessories.

The PTS Enhanced Rail Section for M-LOK is an Airsoft modular rail panel designed to be fit onto M-LOK hand guards, providing a 20mm RIS / RAS rail for mounting Picatinny accessories such as torches, lasers, grips and many other aftermarket attachments. The rail is available in several different lengths depending on what you require. This rail has a sleek look, owing to the weight-reducing corner cuts, keeping your M-LOK rail looking slick!

This rail is the perfect purchase for any Airsoft player who has got their hands on a new rifle with an M-LOK attachment system and is looking to take their gun to the next level by attaching parts and accessories.

A set of two Rail Pieces for KeyMod Handguards, which will provide 3" of 20mm RIS/RAS each. They are easy to install to any KeyMod Rail System, and are a great alternative to purchasing KeyMod compatible accessories.

Those of you wanting to mount an optic or torch closer to your handguard without mounting to the handguard itself, you have found your answer.

Attached to Picatinny system, the mount is offset by 45 degrees, meaning the rail is closer to the barrel, and gives you additional flexibility on where you want your rail and subsequent light/optics etc. mounting. An advantage of this mounting method is that it makes your device easier to reach and use, as well as limiting obstruction to other accessories.

The rail is a 20mm Picatinny type, measuring roughly 2.25 inches and is attached to Picatinny system using the included screws and Allen key. Featuring aluminium alloy construction, the mount is both tough and lightweight, which will complement any loadout.

If you are rocking a KAR98k but you want some modern glass, this is a great way to get the job done! The 20mm Picatinny rail mount from Double Bell is designed to fit to their KAR98K sniper rifle and provide a 20mm rail above the receiver, allowing you to mount modern optical sights. The rail mounts into the rear sight mounting apparatus and provides you with 17 slots of 20mm rail, plenty to mount whatever you like. We advise against adding a PEQ, flashlight and T1 but it's your gun and there is enough space, just be ready to run if a reenactor spots you!

An Alloy constructed rail adaptor for M-LOK handguards, which converts M-LOK slots into 20mm RIS/RAS rails.

Is your AK12 rail scuffed or bent? Need a replacement? No worries. Constructed from lightweight alloy, the cover is easily fit by swapping it out with the original dust cover. With a rail measuring around 7 inches, this cover gives your AK some quality customisation options to which you can attach the sight or scope of your choosing.

Specifically for AK12 models.

The Novritsch SSG10 Full Top Rail Gen.2 allows you to extend your top rail so you can mount any optic you desire atop your Novritsch SSG10. It is a 20mm Picatinny rail so will comfortably harbour most of the common scopes and sights found on the market. The rail screws into the top of your SSG10 receiver with the 4 screws provided, this keeps it securely attached to your sniper rifle, even with the chunkiest of scopes attached!

Make your SSG10 uniquely yours with the Novritsch SSG10 Full Top Rail Gen.2 and mount the perfect scope onto this rail to accommodate your sniping needs.

If you have a TM MK23 you know that bad boy deserves a tactical flashlight or laser aiming module! The Laylax 20mm Picatinny Rail Adapter Version 2 is designed for exactly that and mounts to the ironically named "universal rail" on the MK23 dust cover/frame to provide a rail which actually is universal, the 20mm Picatinny rail.

The adapter itself is constructed from aluminium and has a matt black anodised finish applied, blending perfectly with the MK23's stealthy form. The rail is approximately 7cm long with 5 slots machined in and has a gentle bevel at the front to aid with re-holstering.