All Electric Parts

If you want to breathe new life into your AEG in the form of speed and torque, the Specna Arms BLDC Brushless Motor; Long is calling your name! The BLDC motor is the affordable option in Specna Arms' new brushless motor lineup, offering the same benefits as the top-end DARK MATTER™ motors with a more economical cast aluminium housing. This variant is the 27K option, offering 27,000 revolutions per minute, plenty for a high-speed build but also an asset to any DMR build requiring a high torque solution. 

Brushless Motors boast lower heat build-up, higher torque-to-weight ratio, improved reliability via reduced friction and significantly reduced operating noise when compared to conventional brushed motors. This, the "long shaft" variant is designed for M4/AR-15 derived AEGs, G3, SMG-5 and P90 AEGs and is a relatively simple install job, though you may need to reinforce other parts to cope with the impressive torque and speed delivered by the BLDC motor. 

If you're upgrading your M4, G3, SMG-5 or P90 AEG and seeking more speed for a higher rate of fire or more torque for a better trigger response and the ability to pull strong DMR springs, the BLDC Brushless Motor from Specna Arms is the ideal affordable option!

If you're fed up with your NGRS gearbox locking up when you slap out some double taps, the GATE TITAN™ V2 NGRS Rear Wired; Expert Firmware will cure it! This advanced MOSFET/ETU system replaces the copper trigger contact inside the standard NGRS V2 (aka Version 9) gearbox with optical sensors, eliminating the need for a cut-off lever, extending the lifespan of your AEG and offering unprecedented trigger sensitivity, fire mode and cycle control adjustment options.

The latest version of the TITAN™ V2 NGRS includes the Expert Firmware, meaning you have immediate access to the most advanced programming functions of the TITAN™ without needing to pay more to update the firmware. With the Gate USB-Link or Blulink, you can set your pre-cocking level for a speedy trigger response, adjust your trigger sensitivity, tune active braking and adjust the rate of fire for a truly custom setup that suits your playstyle perfectly. The usual programmable MOSFET functions of other ETUs are also present, including burst mode, binary trigger, semi-auto-only, ramping semi-auto, dual-stage trigger and sniper delay.

This is the Rear Wired version of the TITAN™ V2 NGRS, making it ideal for rear-wired M4, 416 and SCAR NGRS rifles. If you want to speed up your NGRS trigger, use LiPo batteries, run burst mode and protect its internals in the long run, the GATE TITAN™ V2 NGRS Rear Wired; Expert Firmware will give you what you need!

Increasing the rate of fire on your airsoft rifle sometimes causes it to misfeed, resulting in dry firing. A sector gear delay will solve your feeding problems 99.9% of the time with a simple add-on.

This sector gear clip increases the time it takes for the air nozzle to cycle. Delaying the cycle improves BB feeding by allowing the air nozzle to be retracted from the hop-feed for a longer duration.

This tiny add-on could instantly transform your AEG if it has been suffering from firing issues.

Although this is designed to be a perfect fit, it is recommended that this be permanently fixed in place using superglue, after testing to prevent it from potentially loosening over time.

The Airtech Studios Set of 4 Spring Shims;10mm Inner Diameter are designed for most Tokyo Marui spec spring guides. These reinforced polymer shims slide onto the spring guide and add additional tension to the existing spring within the gearbox. The different sizes of shim add different amounts of FPS to your replica. The smallest shim adds roughly 5 FPS to your replica and the largest adds roughly 20 FPS. The shims are designed to be of various sizes so that you can combine them and find the optimal FPS increase to keep your replica within site limits.

These shims give you an easy way to increase your platform's FPS without having to have multiple springs. Simply add or remove the shims as and when you need to adjust your AEGs FPS, with minimal hassle!

If you have stripped your piston and need a replacement, here ya go! The KRYTAC Piston & Piston Head Assembly V2 for M4/AR-15 AEG is a replacement original parts set including a polymer piston with a 4-tooth steel rack and a polymer piston head with pre-installed O-ring. The set is designed for the Krytac Trident AEG series but is compatible with M4/AR-15 AEGs equipped with a version 2 gearbox. 

FPS Softair brings you the Polymer Piston w/Steel Tooth Rack for Marui NGRS SCAR-L/H, featuring a technopolymer body and a full rack of steel teeth for a good combination of high strength and low weight.

The loaded technopolymer assures great mechanical resistance and dimensional precision. The tooth rack was manufactured through the use of MIM (Metal Injection Moulding) technology since this production process guarantees dimensional accuracy and sturdiness equal to those of solid machining.

The metal injected is SAE 4650 steel, currently considered the best for this type of use. The sliding guides are designed to minimize friction and hold the lubricant for a long period of time, so you can be safe in the knowledge that your TM NGRS SCAR will have reliable and long-lasting functionality.

If you're on the hunt for upgraded motors and need maximum speed and torque, the Specna Arms DARK MATTER™ Brushless Motor; Long should fit the bill. This Brushless Motor is Specna's top of the line offering, made with a CNC aluminium housing and available in ultra swift 39K RPM and the diabolically fast 48K RPM variants. This is the "long shaft" version, designed for use in M4/AR-15, SMG-5, G3 and P90 AEGs.

DARK MATTER™ motors are Brushless Motors, similar to the legendary Warhead Industries examples and boasting lower heat build-up, higher torque-to-weight ratio, improved reliability via reduced friction and significantly reduced operating noise when compared to conventional brushed motors. While installing a DARK MATTER™ motor in your AEG will make it a beast, the more important aspect is keeping it performing in the long term. As is always the case with super strong motors, we only recommend the Dark Matter series to those with the technical know-how to ensure their setup can handle it!

If you're on the hunt for upgraded motors and need maximum speed and torque, the Specna Arms DARK MATTER™ Brushless Motor; Long should fit the bill. This Brushless Motor is Specna's top of the line offering, made with a CNC aluminium housing and available in ultra swift 39K RPM and the diabolically fast 48K RPM variants. This is the "long shaft" version, designed for use in M4/AR-15, SMG-5, G3 and P90 AEGs.

DARK MATTER™ motors are Brushless Motors, similar to the legendary Warhead Industries examples and boasting lower heat build-up, higher torque-to-weight ratio, improved reliability via reduced friction and significantly reduced operating noise when compared to conventional brushed motors. While installing a DARK MATTER™ motor in your AEG will make it a beast, the more important aspect is keeping it performing in the long term. As is always the case with super strong motors, we only recommend the Dark Matter series to those with the technical know-how to ensure their setup can handle it!

If you're working on the ultimate AEG build, the Warhead Industries Ronin CNC Brushless Motor; Long Shaft should be on your shopping list! Outdoing even the legendary Warhead CNC Black brushless motors used by Bolster Armouries, the Ronin is the absolute pinnacle of AEG motor technology, boasting improved quality magnets, a titanium shaft assembly, hard-wired spade connectors and a weight-reduced rotor. 

"Ronin" means a wandering Samurai, a reference to the Warhead Industries stator winding master, a single expert with over 20 years of winding experience who hand winds each Ronin motor personally. While the CNC Black motor also has a hand-wound stator, this is done by regular line workers and while precise, cannot match up to the efficiency and quality of the expertly wound Ronin. 

If you want your AEG shooting at its absolute best and maintaining it in the long run, the Warhead Industries Ronin CNC Brushless Motor is essential. Naturally, such a high-performance motor will require expertise to run properly and other reinforced parts to keep up. If you're the techy type and require the best brushless motor on the market, this is it!

If you're working on the ultimate AEG build, the Warhead Industries Ronin CNC Brushless Motor; Long Shaft should be on your shopping list! Outdoing even the legendary Warhead CNC Black brushless motors used by Bolster Armouries, the Ronin is the absolute pinnacle of AEG motor technology, boasting improved quality magnets, a titanium shaft assembly, hard-wired spade connectors and a weight-reduced rotor. 

"Ronin" means a wandering Samurai, a reference to the Warhead Industries stator winding master, a single expert with over 20 years of winding experience who hand winds each Ronin motor personally. While the CNC Black motor also has a hand-wound stator, this is done by regular line workers and while precise, cannot match up to the efficiency and quality of the expertly wound Ronin. 

If you want your AEG shooting at its absolute best and maintaining it in the long run, the Warhead Industries Ronin CNC Brushless Motor is essential. Naturally, such a high-performance motor will require expertise to run properly and other reinforced parts to keep up. If you're the techy type and require the best brushless motor on the market, this is it!

If you're the techy type or want to move to Deans connectors for improved electrical efficiency, the Amass Deans/T-Plug Connector is calling your name! Available in male or female, these high-quality Amass branded connectors provide a strong connection and ultra-low resistance, ideal for Airsoft AEGs, RC vehicles, Drones and other electronics hobbies.

As it pertains to Airsoft, the Male connector should be on the gun side and the Female on the battery side. Make sure you pay attention to polarity when installing either of these and if you're unsure, consult a tech!

If you're the techy type or want to move to Deans connectors for improved electrical efficiency, the Amass Deans/T-Plug Connector is calling your name! Available in male or female, these high-quality Amass branded connectors provide a strong connection and ultra-low resistance, ideal for Airsoft AEGs, RC vehicles, Drones and other electronics hobbies.

As it pertains to Airsoft, the Male connector should be on the gun side and the Female on the battery side. Make sure you pay attention to polarity when installing either of these and if you're unsure, consult a tech!

If you have misplaced a screw from your motor cage during upgrading/maintaining your version 3 gearbox, no need to hunt for the perfect screw! This screw set from Specna Arms provides all the screws necessary to attach your motor cage to the gearbox and secure the motor inside the cage.

A replacement original KRYTAC part which fits version 2, 3, 6 and 7 gearboxes. This cylinder is a Type 1, meaning it has a port in the side intended to reduce the air volume for use on short barrelled platforms (<363mm inner barrel) and prevent the "suck back" phenomenon.

If you've had a cut-off lever failure or you're the techy type who keeps parts on hand just in case, the CYMA Cut Off Lever for V2 Gearbox is ideal. This is a replacement original part constructed from alloy, compatible with most version 2 gearboxes on the market.

An AEG cylinder head for version 2 gearboxes found in M4/AR15 AEGs and SMG-5 AEGs. This KRYTAC part features a dampening pad, intended to reduce the noise from the piston impacting the cylinder head and give you a smoother sounding gearbox. The cylinder head is constructed from high density polymer with a brass inner nozzle and a rubber dampening pad.

Turn your stock ASG Scorpion EVO's HOP-up chamber to a TDC design without having to replace the whole unit. This kit includes everything you need to install the system into your current HOP-up chamber. It is compatible ONLY with ASG Scorpion EVOs and will not fit in any other HOP-up systems.

TDC (Top-Down-Centre) HOP units are incredibly sought after due to the increased friction they add to BBs, which increases the effectiveness of the HOP applied to your BBs. By installing TDC to the stock HOP-up you are guaranteed compatibility with the platform.

The set also includes rubber nubs, these ensure the HOP is stable while BBs accelerate through the unit, further improving the performance and consistency of your ASG Scorpion EVO. This is a very complex installation process and we only recommend it if you are confident in your understanding and ability to fit it to your HOP-up chamber.

This Guarder upgrade spring is compatible with the Tokyo Marui PSG1 gearbox and provides approximately 150 m/s or 492 FPS muzzle velocity on a 0.2g BB. The spring is made from tempered Si-Cr alloy steel wire to provide the strength and resistance necessary.

Upgrade your AEGs piston head to improve air seal and increase the efficiency of airflow through the cylinder. This piston from FPS Softair has ports on the front to push out the O-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB.

Constructed from CNC aluminium Ergal, which has been anodised, the piston head features a smooth precise surface. The piston head has ports on the front to push out the O-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB.

The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape.

This is the most advanced version with 6 ventilation holes for higher speed and rate of fire, double O-ring and ball-bearing. This head is designed for version 2 and 3 gearboxes but may fit other types.

Building a gearbox from scratch? You'll need a shell to get started! The ARCTURUS Version 3 Alloy Gearbox Shell is a reinforced design with a radiused cylinder window, additional material surrounding the cylinder for extra strength and 8mm bearing holes. The rear of the gearbox is also cut for a quick change spring guide. 

The version 3 shell is common to AK, AUG, AR36 and SMG-5K AEGs (not the regular SMG-5, though) so if you need a gearbox shell for any of these platforms this one will be compatible in most cases. 

A drop in MOSFET Kit designed for Tokyo Marui NGRS Recoil Shock Systems, such as the NGRS M4, and the NGRS SCAR. This variation of the Kit comes with the MOSFET Unit, the USB-Link, and is the Advanced version with unlocked features.

An efficient and well-constructed Air Nozzle which is available for a wide range of replicas, and ensures improved durability and smooth operation.

If you are having trigger trouble with your Specna Arms AR36 AEG, the solution is here! This unit is a replacement original part for the SA-G series of AR36 AEG rifles and will require disassembly of the gearbox to install, and soldering, as such it is only recommended for experienced techs and advanced users.

FPS Softair brings you a super high quality M4 piston with a technopolymer body and a full rack of steel teeth for a good combination of high strength and low weight. This is compatible with Tokyo Marui NGRS M4 gearboxes, aka the Version 9 gearbox. Please note, this piston is not compatible with the TM NGRS SCAR-L or SCAR-H. 

The loaded technopolymer assures great mechanical resistance and dimensional precision. The rack was manufactured through the use of MIM (Metal Injection Moulding) technology since this production process guarantees dimensional accuracy and sturdiness equal to those of solid machining.

Currently considered the best for this type of use, the metal injected is SAE 4650 steel. The sliding guides are designed to minimize friction and hold the lubricant for a long period of time, so you can be safe in the knowledge that your AEG will have reliable and long-lasting cycle functionality.

If you've had a piston failure, G&G Armament to the rescue! This 14-tooth AEG piston is compatible with most Airsoft AEGs (NOT PSG-1 or some SR-25s) and boasts a full steel tooth rack for maximum strength. A great replacement part to have around just in case, this piston takes standard AEG piston heads and the tooth rack is full-width, ideal for most sub-350FPS builds. 

If your SMG-5 trigger is a bit worn out or you have a flat trigger inside and you want a more classic SMG-5 look, the CYMA Trigger for SMG-5 AEG is what you need. This trigger is only for SMG-5 AEGs which use a version 2 gearbox and will not fit the version 3 gearbox equipped SMG-5K and SMG-5PDW series. The trigger itself is constructed from alloy and has the curve of the original SMG-5 trigger, making for an appropriately realistic look. Included with the trigger is a trigger return spring, so if you have lost this part you're in luck!

A replacement or upgrade air nozzle for Airsoft electric SMG-5Ks.

If you have damaged your HOP-up unit and are looking for a replacement, CYMA are now offering their original HOP-up units as an aftermarket part. This unit is for the CM.041K and CM.041PDW AEGs, but will not fit the full sized CM.041 AEGs. The unit is constructed from polymer and comes complete other than the HOP-up rubber. The HOP unit, slider, c-clip and HOP nub are all included, so if you have lost or damaged one of these bits you are in luck!

If you need a new nozzle for your CYMA CM.057 or Real Sword Dragonov SVD, CYMA has you covered! The Aluminium Nozzle for CYMA/Real Sword SVD/SVU is constructed from CNC machined aluminium and compatible with the CYMA CM.057 SVD/SVU AEG series and the Real Sword Dragunov SVD AEG. 

This is a replacement original part specifically designed for the Real Sword pattern SVD gearbox used in the CYMA CM.057 series and is not compatible with A&K SVDs or others. If you've built a beast of a DMR with your SVD and you want to get ahead of any potential parts failures this is a great part to have in the toolbox!

If your selector switch is damaged or you lost a bit during maintenance this set can be a lifesaver! The CYMA Ambidextrous Fire Selector Gears for CM.098 is a replacement original part set for the CM.098 series of SR-25 AEGs and includes the internal selector gears and axis for the CM.098 ambidextrous selector switches.