Airsoft Mounts

If you're recreating the latest real-world German DMR rifle, the East Crane 20mm Picatinny Scope & Red Dot Mount for G-417 Replicas will put a smile on your face! Patterned after the mount setup provided with the real steel G28 DMR, this set includes a dual ring mount for either 25 or 30mm monotube scopes and a red dot sight mount with a built-in sunshade, designed for T1 footprint/mounting standard micro red dot sights. The set includes spacers to allow a 25mm monotube scope to be mounted, though by default the dual ring mount fits 30mm monotubes.

Both the scope and red dot mount are constructed from aluminium with steel bolts, nuts and screws, mounting to 20mm Picatinny rails. The dual scope ring includes a 20mm Picatinny rail on the top of each ring which is intended to allow the red dot sight mount to be fitted, though these are removable if you want to use the two mounts on separate platforms. On the right side of the mount, you'll find helpful engraved markings indicating the mounting direction, just like the real deal.

While it is designed to mimic the real G28 mount setup and is ideally paired with the East Crane EC-204 G-417 DMR, this mount setup will work on any platform with 20mm Picatinny rails and the included T1 mount has been sighted on MP5 and G36 platforms used by the German Armed Forces and Police. Whether you're replicating the real steel G28 or looking for a pair of unique mounts packaged together, the East Crane 20mm Picatinny Scope & Red Dot Mount for G-417 Replicas would be a slick setup for your primary!

This High Profile Rail Riser is designed for any 20mm RIS/RAS Accessory, and is designed to lift it up off the Rail. This is particularly useful for those trying to use a Lower Face Mask with a Red Dot Sight, as you might find that you Mask stops you from aiming down your standard Rail System.

Can be fitted to Airsoft Weapons to lift up Sights and Scopes making them easier to use with Full Face Protection and other Masks. 

A quick-detach sling loop point and sling loop for KeyMod rail systems, allowing you to attach a sling to any point on a KeyMod system.

The UNITY mounts are being favoured world wide due to their slim profile & efficient riser, making them an excellent candidate for using with PEQ / Laser pointers mounted on the upper rail.

A steel-constructed sling plate designed to fit on Airsoft M4/15/16 AEG (Electric) Receiver.

A set of Two Scope Rings for 25mm Optics, which easily attach to 20mm RIS/RAS Rail Systems to install your Rifle Scope on an Airsoft Gun. They have a two piece design which makes installation very easy, and come included with an Allen Key to help. These rings are Low Profile, meaning your Scope will be mounted snugly to your Rail System.

The AK series of rifles is famous for many things, but having the best iron sights is not one of them. The AK Rear Sight Rail For Red Dot Optics from 5KU replaces your AK's rear iron sight but retains basic functionality with its built-in emergency backup sights while providing the option to mount a red dot sight!

Designed specifically for Micro red dot sights, the 8 20mm Picatinny rail slots provide plenty of room for larger red dots but it would look rather silly. It's your AK though, make the purists cry if you feel like it!

A set of two High Profile Scope Mount Rings, which will accept a 25mm Optic and easily install to 20mm RIS/RAS/Picatinny Rail Systems. These mounts are High Profile, which means they will hold your Optic a little higher than standard, which is ideal for those who use Lower Face Protection and struggle to aim down their Scope. Being a two-piece design, and coming included with an Allen Key, they are very easy to install.

The QD Sling Swivel Adapter from 8Fields Tactical is intended to work with QD sling sockets to provide a quick swappable sling solution. The set includes a steel QD sling swivel and an extension strap with an elastic cover and a polymer buckle. To connect the adapter to your QD sling socket all you need to do is push the swivel into the socket, where it will lock in place. To remove it simply press the button at the centre of the swivel which will release it from the socket. With this sling adapter you have the choice, you can either mount your sling directly to the steel swivel or make use of the extension strap for a bit more flexibility.

The QD Sling Swivel Adapter from 8Fields Tactical is intended to work with QD sling sockets to provide a quick swappable sling solution. The set includes a steel QD sling swivel and an extension strap with an elastic cover and a polymer buckle. To connect the adapter to your QD sling socket all you need to do is push the swivel into the socket, where it will lock in place. To remove it simply press the button at the centre of the swivel which will release it from the socket. With this sling adapter you have the choice, you can either mount your sling directly to the steel swivel or make use of the extension strap for a bit more flexibility.

The QD Sling Swivel Adapter from 8Fields Tactical is intended to work with QD sling sockets to provide a quick swappable sling solution. The set includes a steel QD sling swivel and an extension strap with an elastic cover and a polymer buckle. To connect the adapter to your QD sling socket all you need to do is push the swivel into the socket, where it will lock in place. To remove it simply press the button at the centre of the swivel which will release it from the socket. With this sling adapter you have the choice, you can either mount your sling directly to the steel swivel or make use of the extension strap for a bit more flexibility.

The QD Sling Swivel Adapter from 8Fields Tactical is intended to work with QD sling sockets to provide a quick swappable sling solution. The set includes a steel QD sling swivel and an extension strap with an elastic cover and a polymer buckle. To connect the adapter to your QD sling socket all you need to do is push the swivel into the socket, where it will lock in place. To remove it simply press the button at the centre of the swivel which will release it from the socket. With this sling adapter you have the choice, you can either mount your sling directly to the steel swivel or make use of the extension strap for a bit more flexibility.

If you have ever missed a kill because you had to pull off target to adjust magnification, this mount was designed with you in mind! The Ghost Quick Zoom Sliding Scope Adjuster for 20mm Picatinny Rail allows you to adjust the magnification of any adjustable mag riflescope with a rotary adjuster from a firing grip while you keep your reticle on target! Gone are the days of awkward body mechanics when adjusting your optic, giving you more opportunity to bag those all important kills in game!

The Quick Zoom Sliding Scope Adjuster is constructed almost entirely from CNC machined aluminium with steel cables and a polymer sliding button and can be fitted to any Airsoft rifle with a minimum top rail length of approximately 38cm. A spacer is included for longer setups, keeping the adjustment cables protected from snags, and also included in the box is an upper scope ring segment with a 20mm Picatinny rail built-in, allowing a micro red dot sight to be added to the setup as a backup. This combination of a dual ring scope mount, sliding button, spacer and an MRDS mount gives you a whole lot of alu for your money, and even more skirmish utility!

A very simple and innovative design. This adaptor secures onto the SMG-7 or SMG-5 sling point of your choice. You can then equip your sling of choice onto the polymer buckle. 

The perfect mount for your torch, able to fit to any 20mm RIS/RAS rail and with 5 adjustable positions.

Those of you wanting to mount an optic or torch closer to your handguard without mounting to the handguard itself, you have found your answer. Attached to M-LOK system, the mount is offset by 45 degrees, meaning the rail is closer to the barrel, and gives you additional flexibility on where you want your rail and subsequent light/optics etc. mounting. An advantage of this mounting method is that it makes your device easier to reach and use, as well as limiting obstruction to other accessories.

The rail is a 20mm Picatinny type, measuring roughly 2.5 inches and is attached to M-LOK system using the included screws, nuts and Allen key. Featuring aluminium alloy construction, the mount is both tough and lightweight, which will complement any loadout.

A set of two High Profile Scope Mount Rings, which will accept a 25mm Optic and easily install to 20mm RIS/RAS/Picatinny Rail Systems. These mounts are High Profile, which means they will hold your Optic a little higher than standard, which is ideal for those who use Lower Face Protection and struggle to aim down their Scope. Being a two-piece design, and coming included with an Allen Key, they are very easy to install.

If you want to take pure advantage of the SSP5's incredible range and accuracy, an optics mount will get you there! The Novritsch 20mm Picatinny Top Rail for SSP5 GBB Pistol is compatible with all variants of the SSP5 GBB and is constructed from CNC machined aluminium for a perfect combination of low weight, high strength and flawlessly in-spec rail dimensions.

The Top Rail is available in two different lengths, a short version measuring approximately 6cm long and a longer version measuring approximately 10.1 cm. The rail is installed on the optics mount section of the fixed SSP5 outer barrel, meaning it says put while you tap tap tap that trigger for easier target acquisition and less chance your optic will take damage from recoil. If you are running your SSP5 as a primary, this mount is essential to make the most of its epic performance!

A set of two High Profile Scope Rings for 30mm Optics, that will easily connect to 20mm RIS/RAS Picatinny Rail Systems. They have a two-piece design which makes installation very easy, and comes included an Alley Key to aid installation. They are High Profile Rings which will hold the Scope higher than standard, making it easier to aim whilst wearing Lower Face Protection.

Not a fan of SMG-5 dioptre sights? I'm not sure how, but if they don't suit you then here's a way you can still shoot sharp with your SMG-5/MP5 AEG. Allows mounting of red dot sights and shorter length magnified optics. Looks extra cool with an MRDS on!

A pair of scope mounts designed to raise your optic for a more comfortable optic setup.

A pair of scope mounts designed to raise your optic for a more comfortable optic setup.

A high strength sling plate constructed from a dense Alloy that allows you to attach a sling to your AK47 platform weapon.

A pair of 20mm RIS compatible raised scope mount rings, designed to raise up optics to the user's eye-level, or fit larger scopes onto their Airsoft guns. 

A set of Alloy constructed Scope Rings for 30mm Optics, that has a 20mm Mount on each ring for easy installation to a 20mm RIS/RAS/Picatinny Rail System. They are Low Profile Rings, which will hold your Optic low against your rail rather than reaching for the sky.

If you're following modern real steel trends and want a red dot on your sidearm, Airsoft Artisan has what you need! The RMR Mount w/ Front & Rear Sight for WE EU17 GBB includes a front and rear sight with an integral RMR footprint mount plate, allowing you to rock an RMR-style red dot sight paired with a cutting-edge iron sight setup on your WE EU series GBB pistol. 

The front sight includes a red light-enhancing insert and the rear sight features anti-glare checkering, giving you an up-to-date sight setup which is great in both bright and dark conditions. The sights are also set at "suppressor height", meaning if you've got a sneaky build planned or are running a tracer you can still get a clean sight picture. 

The plate itself is designed for RMR footprint red dot sights, meaning most RMR clones should fit including our PCS Miniature Red Dot Reflex Sight. This set is designed for the WE EU17 GBB and as such should also fit WE EU19 and EU34 GBB pistols but won't fit WE EU18 GBB pistols due to their redesigned slide. If your EU series needs a touch of modernity, the Airsoft Artisan RMR Mount w/ Front & Rear Sight for WE EU17 GBB will provide!

If you want to snipe with your KAR98K this should help you get there! The Double Bell Scope Mount For KAR98K is designed specifically for the Double Bell KAR98K and mounts to the receiver rail on the left side of the rifle, just below the rear iron sight. The mount is intended for scopes with a 20mm monotube and is constructed from alloy with steel screws and a steel release lever.

When choosing a scope for this mount we recommend looking for a scope with an objective lens of less than 30mm in diameter, a 20mm monotube and long eye relief due to the "Scout" style mount location positioned closer to the front of the rifle than the average scope mount.

The WADSN 5 Position Flashlight Mount is a great way to attach your flashlight to your platforms. It mounts to a 20mm RIS/RAS rail, which is the most common rail found on rifles and SMGs. There is a choice of black or dark earth so you can match the mount perfectly to fit the style of your loadout. It features 5 adjustable positions so you can find the perfect setup for your loadout and ensure you dominate any CQB skirmish!

To fit your flashlight you must first loosen the two screws found at the front and back of this mount, once loose, you can slide your torch in. Afterwards, tighten the screws up again and your flashlight and mount are ready to go! The polymer construction means you don't need to worry about having a front-heavy Airsoft gun once fitted. Mount your flashlight using the WADSN 5 Position Flashlight Mount and become a master of close-quarters surprise engagements!

The WADSN 5 Position Flashlight Mount is a great way to attach your flashlight to your platforms. It mounts to a 20mm RIS/RAS rail, which is the most common rail found on rifles and SMGs. There is a choice of black or dark earth so you can match the mount perfectly to fit the style of your loadout. It features 5 adjustable positions so you can find the perfect setup for your loadout and ensure you dominate any CQB skirmish!

To fit your flashlight you must first loosen the two screws found at the front and back of this mount, once loose, you can slide your torch in. Afterwards, tighten the screws up again and your flashlight and mount are ready to go! The polymer construction means you don't need to worry about having a front-heavy Airsoft gun once fitted. Mount your flashlight using the WADSN 5 Position Flashlight Mount and become a master of close-quarters surprise engagements!