Airsoft Under £25

A tough and durable Open Top Holster which is made from Kydex material to a high standard, offering you a stable belt-mounted platform to effortlessly holster and unholster a wide variety of sidearms, from the EU-Series to the CZ Family.

A tough and durable Open Top Holster which is made from Kydex material to a high standard, offering you a stable belt-mounted platform to effortlessly holster and unholster a wide variety of sidearms, from the EU-Series to the CZ Family.

The No.691 Delphis Waterproof Medical Case is a rugged Hard Case made from Polypropylene (PP) + Glass Fibre Resin Material, with Pick and Pluck Foam internals and seriously tough hinges supported by Stainless Steel pins. Despite the name, this Hard Case can be put to any use and labelled appropriately using the Name Tag Slider. Easily stackable, if you need to transport delicate/sensitive equipment from A to B and want to know it's fully protected from Water, Dust, Impacts and Extreme Temperatures, then you're in the right place.

If you need to transport valuable equipment from A to B, and you need to know that the contents are safe from the ingress of Water and Dirt, Extreme Temperatures as well as Pressure changes and rough impacts, then you need the No.649 Cobra Hard Case. Made from Polypropylene (PP) + Glass Fibre material, with interior Pick and Pluck Foam that can be cut to perfectly match the contents, you can be sure that your valuable equipment is safe.

A Maple Leaf inner barrel for Gas Blowback Airsoft Pistols.

If your loadout involves a tuxedo, or you are a loose cannon cop on the edge who doesn't play by the rules, you may want to take a look at this shoulder harness from CYTAC. The harness allows you to mount a CYTAC holster or magazine pouch (not included) on either of the two platforms, converting your hip or leg-mounted setup into a classy af shoulder holster setup.

If you're looking for magazines for your big boy AR, the East Crane 130rnd Steel Mid-Cap Magazine For SR25/AR10 AEG should do the trick! This magazine is constructed with a stamped steel shell and polymer internals, patterned after real steel SR25 20-round magazines and holding 130 BBs. Like other Airsoft mid-caps, this mag is loaded through the fill/feed port on the top of the magazine body using a speed loader or loading tool. 

Compatibility-wise, this magazine is for SR25 AEGs and will not fit standard M4/AR-15 receivers. Patterned after the Classic Army SR25 magazine style, this mag should fit East Crane, Classic Army, CYMA and A&K SR25 AEGs but won't fit G&G SR25s due to their different magazine design. 

The MEC M-Valve from PTS is designed to improve gas efficiency and speed up the cyclic rate of your Tokyo Marui EU17 GBB pistol. The valve is constructed from high strength brass with rubber O-rings and should help improve the performance of your pistol in cold weather, and speed up the cyclic rate if you have installed a heavy steel slide.

If you have broken your APS UAR trigger with some heavy fingered action we have the solution! The APS Trigger for UAR AEG is a replacement part for the UAR AEG and includes the trigger itself, trigger axis pin and trigger spring. 

If you are styling your AAP-01 up this part would be great to add a bit of flair to your custom job. The Upper Receiver Lock Button from CowCow is constructed from aluminium, making it stronger than the original, but more importantly, it is available in several exciting colour options! Available in tactical black for more discrete builds or gold, red and glorious heat gradation for those looking for a more eye-catching pistol, the CowCow upper receiver lock button is great for any AAP style!

If you are styling your AAP-01 up this part would be great to add a bit of flair to your custom job. The Upper Receiver Lock Button from CowCow is constructed from aluminium, making it stronger than the original, but more importantly, it is available in several exciting colour options! Available in tactical black for more discrete builds or gold, red and glorious heat gradation for those looking for a more eye-catching pistol, the CowCow upper receiver lock button is great for any AAP style!

A Polymer constructed Retention Holster for Airsoft P99 GBB pistols, which attaches to a belt via the paddle. The holster features an adjustable draw angle and compatibility with Amomax accessories such as their MOLLE mount and shoulder harness.

Upgrade your AEGs gearbox to improve shot consistency thanks to a better air seal. The cylinder head is constructed from CNC Ergal and is anodised with a smooth surface finish, precisely engineered so that the tolerance is not affected. Features powerful built in UREPAN bumper that absorbs the shock from the piston head.

This cylinder head is suitable for Tokyo Marui NGRS or version 9 gearbox. The hardness of the yellow rubber is 60 degrees shore, with a good balance between air seal and strength making it suitable for use in a custom DMR, as well as helping to protect the gearbox and reduce noise.

This Hard Case is designed to protect your Passport, Phone, Camera and more from the elements, in a transparent and easy to use Case. Whether you need protection from the ingress of Water or Dust, the effects of extreme Temperature or just simple physical damage, then the PARRA LITE Hard Case will perfectly fill the role.

If you are tuning your gearbox for a high rate of fire build a reinforced tappet plate is a must for your shopping list. The Perfect Tappet Plate from Laylax replaces your original tappet plate to keep your AEG running for longer at high speed thanks to its reinforced polymer construction. 

Upgrade your AEGs piston head to improve air seal and increase the efficiency of airflow through the cylinder. This piston from FPS Softair has ports on the front to push out the O-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB.

Constructed from CNC aluminium Ergal, which has been anodised, the piston head features a smooth precise surface. The piston head has ports on the front to push out the O-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB.

The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape.

This is the most advanced version with 6 ventilation holes for higher speed and rate of fire, double O-ring and ball-bearing. This head is designed for version 2 and 3 gearboxes but may fit other types.

A 600rnd High Capacity Magazine for the LCT LK-33 Series, made with a highly realistic Steel Outer Shell to closely match the real thing. It is filled by pouring BBs in through the top Fill Window, and wound at the base of the Magazine to feed BBs into your Gun. If you own an LCT LK-33 Series Airsoft Electric Gun and want to stay in the fight for longer without re-filling Magazines, then the LCT LK007 LR-223 600rds Magazine is ideal.

This is a Truck Cap/Hat for Airsoft or everyday general use, it is constructed from 50% Cotton and 50% Polyester, reinforced with a Rip-Stop weave. The pattern is a unique camo called MAPA camo, and resembles a spill stain disruptive pattern. The hat is adjustable via the back strap that has a section of button clips allowing you to fit it to your head perfectly.

A classic front sight design that has been around for quite some time in the Airsoft world, this sight is usually found on KAC style replicas such as the KAC PDW, SR-25, and SR-15, but is perfectly suitable for a civilian tactical M4 build or an MK12 SPR build. The sight mounts to a 20mm Picatinny rail and is adjustable for elevation by raising and lowering the steel front blade/post using an M4/AR15 front sight adjustment tool. This sight is very sturdy and well built, making it perfect for anyone who has had bad luck with polymer sights. The sight was intended to be equally effective in use as a primary aiming device as it is as a backup sight for your optic. This sight is incredibly low profile when folded, and is perfect for setups with a big scope that would prevent bulkier flip-up sights from mounting. 

Looking to give your CM.706 Sniper rifle a bit more range? The CYMA Upgrade set for CM.706 will give you what you seek, with the added benefit of including reinforced parts! The set includes the piston, piston head and spring guide, all of which are machined from aluminium and finished in metallic blue, and a seriously high power spring which gives out approximately 575 FPS when installed!

If you've lost a selector switch from your ARCTURUS AR15 Lite AEG, this set will sort you out! The Ambidextrous Selector Switch Set for AR15 Lite Series from ARCTURUS is an original replacement parts set specifically for the ARCTURUS AR15 Lite AEG series and is unlikely to fit other brands and models of M4 AEG. 

The set includes both selector switches, the mounting bolts, the detent and detent spring, replacing the entire external selector mech of the AR15 Lite. If you had a mid-game mishap and lost a selector switch, this set will get you up and running again!

If you are working on your CQB build you must be looking for an extremely short outer barrel, and this one certainly is that! The 5KU 8.7" Aluminium Outer Barrel For M4/AR-15 AEG is compatible with most M4/AR-15 AEGs and is constructed from aluminium for a perfect balance between low weight and high strength. 

The barrel is threaded at the tip with common 14mm CCW male threading, meaning you can mount the most common muzzle devices on the market with ease, including tracer units, suppressors and flash hiders in various styles. Also present are grooves in the underside to allow a gas block or M4/AR-15 triangular front iron sights to be mounted, though this is not essential. If you need your M4 Airsoft rifle to be shorter this will get you halfway there, but don't forget you'll need a shorter inner barrel to match!

This Guarder upgrade spring is compatible with the Tokyo Marui PSG1 gearbox and provides approximately 150 m/s or 492 FPS muzzle velocity on a 0.2g BB. The spring is made from tempered Si-Cr alloy steel wire to provide the strength and resistance necessary.

If you need a battery for your AR36 AEG or polymer handguard equipped M4/AR-15 AEG this one will do the trick! The 7.4v 1800mAh 20C LiPo Flat Nunchuck Battery from Electro River is a flat nunchuck style battery, also known as a "butterfly" configuration. Unlike other nunchuck batteries, this won't inside a crane stock and is more suitable for large polymer handguards such as those found on AR36 and M4A1 AEGs and will also fit nicely in most fixed rifle stocks.

The battery itself is a 2-cell 7.4V LiPo with a wire length of approximately 9cm between the cell groups and the connector, and each of the two cell groups measures 10 x 0.6 x 3.5cm approximately. The pre-wired connector is the common mini-Tamiya type and the continuous discharge rate is 20C, with a maximum discharge rate of 40C.

If you like to be at the cutting edge of battery technology when it comes to Airsoft, you're going to want to check this out! The Gens Ace 7.4V 25C 1000mAh Airsoft LiPo Battery - Mini-Tamiya is a slim LiPo battery intended for Airsoft buffer tube battery compartments, AK top covers and other cramped spaces requiring a single cell group. The discharge rate is 25C, giving you a snappy response without risking overspin in most setups, and the capacity is 1000mAh, meaning you might need two to get through a full game day. 

Where this battery differs from the norm is its Smart Balance Connector which interfaces with the Gens Ace IMARS Mini Charger, communicating the battery type and current charge levels and immediately commencing optimal charging as soon as this "Smart Battery" is connected. Compared to legacy smart chargers, this saves loads of time but unfortunately means that this battery cannot be charged using a standard LiPo balance charger. 

FPS Softair brings you a super high quality M4 piston with a technopolymer body and a full rack of steel teeth for a good combination of high strength and low weight. This is compatible with Tokyo Marui NGRS M4 gearboxes, aka the Version 9 gearbox. Please note, this piston is not compatible with the TM NGRS SCAR-L or SCAR-H. 

The loaded technopolymer assures great mechanical resistance and dimensional precision. The rack was manufactured through the use of MIM (Metal Injection Moulding) technology since this production process guarantees dimensional accuracy and sturdiness equal to those of solid machining.

Currently considered the best for this type of use, the metal injected is SAE 4650 steel. The sliding guides are designed to minimize friction and hold the lubricant for a long period of time, so you can be safe in the knowledge that your AEG will have reliable and long-lasting cycle functionality.

The No. 529 Boomslang Hard Case is named after the Sub-Saharan Snake and will protect the contents stored inside with the same effectiveness. Ok, maybe it doesn't have life-threatening Venom, but it is independently tested, assured and certified by Intertek to be Waterproof, safe from Impacts and Crushing, as well as protected from Extreme Temperatures ranging from -40°C to 90°C. With several layers of Eggbox, Protective and Pick n' Pluck foam inside, you can depend on the Boomslang to protect any sensitive or delicate equipment inside.

If you're running an M82A1 AEG, you need some spare mags for it, and AEGs work best with high-caps, right? This mag from Snow Wolf has a whopping 500 round capacity and is wheel wound from the bottom so you won't be switching mags any time soon.

Constructed from lightweight polymer, this mag helps keep the weight of your huge Barrett down. So grab this mag and start picking people off en masse!

Building a gearbox from scratch? You'll need a shell to get started! The ARCTURUS Version 3 Alloy Gearbox Shell is a reinforced design with a radiused cylinder window, additional material surrounding the cylinder for extra strength and 8mm bearing holes. The rear of the gearbox is also cut for a quick change spring guide. 

The version 3 shell is common to AK, AUG, AR36 and SMG-5K AEGs (not the regular SMG-5, though) so if you need a gearbox shell for any of these platforms this one will be compatible in most cases. 

A must have battery for any avid RC user or Airsofter that requires enough power to last all day of full auto or a full weekend Milsim.