All Airsoft Batteries

A stick 7.4v 1100mAh LiPo designed and built by NUPROL specifically for Airsoft Skirmishers and are part of their POWER range of Batteries, intended to allow Airsofters to get the best possible performance from their Airsoft Electric Guns.

Tried and true, everyone has use for NiMh crane stock batteries! The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance so you can use any charger as long as it's NiMh compatible, just make sure to not leave the battery charging unattended.

This battery has a voltage of 9.6v and a capacity of 1600mAh and is comprised of 8 cells working in unison, connected via the Mini-Tamiya connector.

This NiMh sports a crane configuration, one of the most common types and is perfect for split battery compartments, most commonly seen in M4 stocks, M16, SMG-5 and AKs with full stocks. The battery measures 12x1.8x1.8cm per 4x cells, with a wire length of roughly 8cm.

A quality battery produced by VP Racing and designed for electronic products such as Airsoft AEG rifles and remote controlled cars etc. Holding a charge of 9.6V at 1600mAh, this battery will easily last all day of Airsoft gaming.

High quality WE 11.1v 1450mAh 30C LiPo Stick Battery, provides great battery life and fits most battery compartments. The 30C rating means the battery discharges quicker to give a higher rate of fire and better trigger response.

VP Racing are well known for their high quality and high performance batteries with this one being a crane form factor. The battery has a voltage of 7.4v, has a capacity of 1450mAh and a discharge rate of 25C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with Deans connector, however adaptors are available.

The battery consists of two cells working in tandem, with each cell measuring 13x0.7x2cm each with a cable length of roughly 7.5cm of wire. The battery should fit in crane stock battery compartments such as M4s and some handguards and full stocks, but remember to measure up before hand!

A LiPo battery for Airsoft Electric Guns which has been designed to output a high power for fast and consistent trigger response and high rate of fire for up to 3 quarters of a day on a slow charge. 

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too, and is designed to give you a high output for fast rate of fire and trigger response for roughly half a day dependent on trigger happiness.

A high quality 1300mAh 7.4V LiPo battery suitable for Airsoft and RC use - perfect for fitting down stock tubes and areas with a small amount of space.

An ultra thin and lightweight battery, perfect for squeezing into even the tightest spots. The battery provides 1200mAh of power with a discharge rate of 20c, giving it a 20w output. 

A compact LiPo Airsoft battery, designed to be used in tight awkward spaces, without compromising on overall capacity.

An Airsoft Gun Battery designed and built by NUPROL specifically for Airsoft Skirmishers and are part of their POWER range of Batteries. 

A large stick type battery, designed to output a high power for fast trigger response and rate of fire for up to three quarters of a day on a slow charge.

A high quality 11.1V LiPo battery with a 1200mAh capacity, suitable for both Airsoft and RC use.

A high powered Airsoft Battery, designed to be used in highly tuned top-end gearbox. The battery comes in a 'stick' configuration, with two adjoined cells in one block, allowing the battery to be squeezed into even the tightest of buffer tubes. 

A super thin, triple cell crane stock styled 11.1v LiPo battery, featuring a small Tamiya connector for easy use.

A large stick type LiPo battery, ideally suited to fitting inside an M4 or M16 type AEG stock tube.

A high voltage Airsoft Battery designed to give your weapon the highest rate of fire possible, in addition to lasting as long as possible, reducing the amount of time players spend changing batteries on a Skirmish day. 

A high output VP Racing 11.1v 1450mAh LiPo battery, designed to deliver some serious rate of fire and trigger response with the right setup.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too. 

A 23cm long 9.6v NiMH stick battery, ideally suited for powering top wired AEGs such as the AK47 and other weapons with a long and thin battery compartment.

If you need a compact Airsoft battery which fits almost anywhere the 7.4v 1100mAh 20C LiPo Crane Battery from VAPEX is ideal. This battery is pre-wired with a mini-Tamiya battery connector and each cell unit measures 11 x 0.7 x 2.2 cm with approximately 9 cm of wiring between each cell and the connector, making it great for tight spaces and use with multiple different platforms.

The compact size of this crane/nunchuck battery makes it ideal not only for Airsoft but also for electronics hobby applications and R/C when a lightweight and compact power source is a priority. Whether it needs to fit into a buffer tube, crane stock, handguard or practically anywhere else this super slim battery is perfect, especially if you want a single battery which fits in multiple guns!

Those of you looking for a battery with a large capacity in a medium-sized block form factor, you've come to the right place! The battery is perfect for larger areas such as full-stocked SMG-5, G3, M16 and AK platforms, AR36 handguards and full-stock rifles. The battery has a voltage of 7.4v, a capacity of 2300mAh and a continuous discharge rate of 20C with a maximum discharge rate of 40C. The battery is connected to your AEG via the Mini-Tamiya connector, not to be confused with a Deans connector, however, adaptors are available.

The battery measures 10x1.5x3.4cm with a cable length of roughly 10cm.

If you are looking for a decently sized crane stock battery which should last all day, the VAPEX 7.4v 2200mAh 20C LiPo Crane Battery should do the trick! This battery is a 7.4V 2S LiPo in crane/nunchuck configuration, meaning the cells are separated into two individual units which makes the battery far easier to fit into unconventionally shaped battery compartments. The pre-wired connector is the common mini-Tamiya connector and the continuous discharge rate is 20C.

Each of the individual cell units measures 11x2.2x1.2cm approximately with a wire length of 9cm between each cell and the connector, meaning this should fit nicely in most crane stocks and many handguards and full-stock battery compartments, though as always, we advise measuring carefully before ordering!

A 9.9V LiFe (Lithium Iron Phosphate) battery for Airsoft, RC and other hobbies. Ideally suited to sit in a handguard or stock, this battery provides a higher voltage (and rate of fire) over standard Airsoft batteries.

This Airsoft Battery and Charger pack features a NUPROL 9.6v 1600mAh Ni-Mh Crane Battery, NUPROL NPC-01 NiMh Battery Charger, and Safe Charging Bag which are perfectly matched to work with each other, a great choice for anyone new to Airsoft and looking for a battery for their gun. 

If your Airsoft gun comes with a sample 9.6v Block or Crane style battery and charger then this is one of the first things you should buy. The battery will last longer, charge better, and will be of much higher quality than the free gift battery included for testing in some Airsoft gun boxes!

A compact yet high output LiPo battery designed for most M4 stock tubes, solid stocks and some hand guards.

A super thin triple crane stock 11.1v 1300mAh 25C LiPo that features a standard Tamiya connector and is made up of three individual thin cells, making it great for squeezing into awkward spaces.

If you need a battery for your M4/AR-15 AEG buffer tube and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configurations with a Mini-Tamiya connector; an ideal setup for a Mini-Tamiya equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2x cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

A LiPo crane stock battery designed to fit in stocks and small spaces which other large batteries do not fit.

A LiPo crane stock battery designed to fit in crane and solid stocks, where other batteries would be wasting the available space.