All Electric Parts

A replacement or upgrade air nozzle for Airsoft electric SMG-5Ks.

If you have damaged your HOP-up unit and are looking for a replacement, CYMA are now offering their original HOP-up units as an aftermarket part. This unit is for the CM.041K and CM.041PDW AEGs, but will not fit the full sized CM.041 AEGs. The unit is constructed from polymer and comes complete other than the HOP-up rubber. The HOP unit, slider, c-clip and HOP nub are all included, so if you have lost or damaged one of these bits you are in luck!

If you need a new nozzle for your CYMA CM.057 or Real Sword Dragonov SVD, CYMA has you covered! The Aluminium Nozzle for CYMA/Real Sword SVD/SVU is constructed from CNC machined aluminium and compatible with the CYMA CM.057 SVD/SVU AEG series and the Real Sword Dragunov SVD AEG. 

This is a replacement original part specifically designed for the Real Sword pattern SVD gearbox used in the CYMA CM.057 series and is not compatible with A&K SVDs or others. If you've built a beast of a DMR with your SVD and you want to get ahead of any potential parts failures this is a great part to have in the toolbox!

If your selector switch is damaged or you lost a bit during maintenance this set can be a lifesaver! The CYMA Ambidextrous Fire Selector Gears for CM.098 is a replacement original part set for the CM.098 series of SR-25 AEGs and includes the internal selector gears and axis for the CM.098 ambidextrous selector switches. 

The Airtech Studios Set of 4 Spring Shims;11mm Inner Diameter are designed for most VFC, Krytac & ASG spec spring guides. These reinforced polymer shims slide onto the spring guide and add additional tension to the existing spring within the gearbox. The different sizes of shim add different amounts of FPS to your replica. The smallest shim adds roughly 5 FPS to your replica and the largest adds roughly 20 FPS. The shims are designed to be of various sizes so that you can combine them and find the optimal FPS increase to keep your replica within site limits.

These shims give you an easy way to increase your platform's FPS without having to have multiple springs. Simply add or remove the shims as and when you need to adjust your AEGs FPS, with minimal hassle!

If you are having trigger issues with your ARCTURUS AK AEG this replacement original part set should cure it! The ARCTURUS Microswitch V3 for ARCTURUS AK series includes the microswitch itself, a Deans/T-plug battery connector and spade connectors all wired together for a relatively simple installation procedure. The set should not require soldering to install, but as always, we recommend a certain level of confidence and expertise if you plan on installing this part.

If you are tuning your gearbox for a high rate of fire build a reinforced tappet plate is a must for your shopping list. The Perfect Tappet Plate from Laylax replaces your original tappet plate to keep your AEG running for longer at high speed thanks to its reinforced polymer construction. 

Bolster Armouries EZO Ball-Bearing Bushings are designed and manufactured by Sapparo Precision Inc. in Japan and have been chosen by the Bolster team thanks to their extremely low friction, high-quality steel construction and fantastic reputation in a wide range of industries.

Specialists in medium and miniature ball bearings, Sapporo Precision bearings have a wide range of applications; in this case, reducing friction and extending the lifespan of whichever AEG they're installed inside. These bearings allow the gears to spin freely at a tremendous rate under high stress with minimal chances of failure, all while reducing stress on the gearbox shell and gear axles.

These are the same bearings used in Bolster Armouries' ultra high-end ONYX [Violet Edition] and ONYX [Blackout] builds and have performed phenomenally, proving to be far stronger than the average ball-bearing bushings. Compatibility-wise, these EZO Bearings will fit any AEG gearbox shell with 8mm bushing holes. If you want a super slick smooth running AEG build, Bolster Armouries EZO 8mm Japanese Steel Ball Bearing Bushing Set belong inside! 

A Generation 3 Micro Computer Controller Chip Set designed to add a huge variety of functionality to Airsoft AEG. The chip is built to be as compact as possible, requiring the smallest amount space and is specially coated to the Military Specification (Mil-Spec) MIL-V-173C. 

If you're looking to revamp your old SR25 why not take a walk on easy street and replace the whole gearbox? The CYMA CM.098 SR25 V2 Long Gearbox Set w/Motor is the exact gearbox used in their CM.098 SR25 series and should be compatible with Classic Army style SR25 AEGs which use the version 2 long gearbox (Classic Army, CYMA and A&K). This gearbox is well equipped, and includes a MOSFET/ETU prewired in, a quick change spring system, an M130 spring and also includes a high torque Neodymium magnet motor. Perfect to fix up an old big boy AR!

If you're running a P90 and want to spice it up a notch, the Perun Optical MOSFET/ETU for P90 AEG is what you need to take your P90 to the next level. This advanced MOSFET/ETU uses optical sensors to speed up your P90 and provide programmable functions, including burst mode, binary trigger, adjustable active braking, adjustable pre-cocking, trigger sensitivity adjustment and compatibility with dual sector gear setups. 

Make no mistake, this MOSFET rivals the incredible Gate TITAN and ASTER series in the functions and performance it provides. Unlike the Gate 'fets, the Perun is designed specifically for TM P90-based AEGs, meaning no compatibility worries and a relatively easy installation process. If you want your P90 to shoot like an upgraded M4 platform, this is how you do it!

If you are building a version 3 AK gearbox or you have an old AK AEG that needs a refit, this spring set will be useful! The set includes all the springs needed to complete a version 3 gearbox for AK AEGs except for the mainspring (the spring that provides the power). Maybe you have lost a spring, or your tappet spring got chewed up after a long and hard life? This spring set should give you all you need to get your AK doing its dirty work once again!

A vital spare for Version 3 gearboxes.

If you have worn out your trigger or you're looking for a milspec trigger to replace a speedyboi flat trigger, this should do the trick! The Krytac Trident Trigger for M4/AR-15 AEG is constructed from alloy and is patterned after the standard curved "Milspec" trigger found on the M4A1 rifle, MK18 MOD.0 and MOD.1 as well as practically any other M4/AR-15 used in military service in the real world.

The trigger is designed for the version 2 gearbox found in the vast majority of M4/AR-15 AEGs, meaning this trigger should work in practically any M4/AR-15 AEG but will require the gearbox to be opened up to install it. 

Designed specifically for the Gate EON CNC Rotary HOP-up chamber, the Airtech Studios Full Upgrade Set for Gate EON HOP-up Chamber includes a TDC trolley, 2 x M-nubs and an inner barrel centring unit. This set is designed to convert the Gate EON into a true TDC unit, giving you more range and accuracy than ever before!

The benefits of a TDC HOP-up unit include a stronger HOP-up effect and less chance of side-to-side shot deviation when using heavy BBs at high FPS. This part will require a certain amount of expertise to install but thankfully, the process is fully explained on the Airtech Studios website. If you want to get the most out of your Gate EON HOP-up chamber, this kit will do the trick!

If your CYMA CM.098 or CM.057 needs a revamp, the CYMA Stainless Steel Cylinder for CM.057 SVD & CM.098 SR-25 AEGs should be of use. This stainless steel cylinder is ribbed to promote heat dissipation and polished on the inside for minimal friction. 

This cylinder is a standard bore unported cylinder and is compatible with version 2 long gearboxes found in CA/A&K SR-25 AEGs and CYMA CM.098 SR-25 AEGs and also fits the Real Sword spec SVD gearbox used in the CYMA CM.057 SVD/SVU series and the Real Sword SVD Dragunov. 

The EPeS Airsoft Nozzle series is a line of super durable, high performing Airsoft Electric Nozzles designed to massively improve the performance and longevity of your airsoft gun.

A replacement / spare for stock or damaged bearing in Version 6 (V6) and Version 7 (V7) Gearbox. In gearbox spring guides are designed to help the spring in its correct position. 

A set of tempered Bushings from Modify which comes included with installation tools.

If your CYMA MOSFET has met its end, or you want a cheap and cheerful upgrade, the CYMA MOSFET for V2 Gearbox is ideal. This MOSFET is a replacement original part for the CYMA Platinum AEG series and should work with any AEG which uses a version 2 gearbox. When installed, this MOSFET should improve trigger response and rate of fire, along with eliminating the chances of your trigger contacts becoming corroded. 

The MOSFET is pre-wired with two sets of spade connectors and you can choose between rear-wired and front-wired configurations. Please note, certain gearboxes will need modification to install this MOSFET/ETU unless they already have a slot in the shell designed for an electronic trigger. We only recommend this part for experienced users! 

This SR25 Gearbox set by CYMA is designed to fit right into most SR25 / AR25 / AR10 style Airsoft Rifles / Guns. Included is a Piston, Cylinder, Gear Set, Tappet Plate, Nozzle. This GEARBOX set does not come with the shell, internals only.

If you're working on a long-barreled AR36 AEG build, whether it's a DMR or an MG36 LMG, the FPS Softair Full Tune Up Kit for AR36 AEGs is the ideal addition to your build. This kit includes replacements for the full cylinder group, enhancing air seal, and improving longevity and overall efficiency.

The kit is optimised for inner barrels of 451-550mm in length and includes a Type F CNC Steel Cylinder, ERGAL Nozzle with O-ring, CNC Aluminium cylinder head and a CNC ERGAL Double O-ring ball-bearing advanced piston head. If you're looking for maximum efficiency and strength from your long-barreled AR36 build, you need this kit!

If you have a high-speed or DMR build planned with an AR36, AK, SG55x or AUG base gun, the Specna Arms DARK MATTER™ Brushless Motor; Short belongs inside! This beastly brushless motor is top-of-the-line in Specna's new motor range, offering a high-quality CNC aluminium housing with powerful brushless motor technology inside. This is the short shaft variant designed for AR36, AK, SG55x and AUG AEGs and is offered in 34K, 39K or 48K RPM flavours, ideal for any build objective which demands extreme speed and torque!

DARK MATTER™ motors are Brushless Motors, similar to the legendary Warhead Industries examples and boasting lower heat build-up, higher torque-to-weight ratio, improved reliability via reduced friction and significantly reduced operating noise when compared to conventional brushed motors. While installing a DARK MATTER™ motor in your AEG will make it a beast, the more important aspect is keeping it performing in the long term. As is always the case with super strong motors, we only recommend the Dark Matter series to those with the technical know-how to ensure their setup can handle it!

If you have a high-speed or DMR build planned with an AR36, AK, SG55x or AUG base gun, the Specna Arms DARK MATTER™ Brushless Motor; Short belongs inside! This beastly brushless motor is top-of-the-line in Specna's new motor range, offering a high-quality CNC aluminium housing with powerful brushless motor technology inside. This is the short shaft variant designed for AR36, AK, SG55x and AUG AEGs and is offered in 34K, 39K or 48K RPM flavours, ideal for any build objective which demands extreme speed and torque!

DARK MATTER™ motors are Brushless Motors, similar to the legendary Warhead Industries examples and boasting lower heat build-up, higher torque-to-weight ratio, improved reliability via reduced friction and significantly reduced operating noise when compared to conventional brushed motors. While installing a DARK MATTER™ motor in your AEG will make it a beast, the more important aspect is keeping it performing in the long term. As is always the case with super strong motors, we only recommend the Dark Matter series to those with the technical know-how to ensure their setup can handle it!

If you have a high-speed or DMR build planned with an AR36, AK, SG55x or AUG base gun, the Specna Arms DARK MATTER™ Brushless Motor; Short belongs inside! This beastly brushless motor is top-of-the-line in Specna's new motor range, offering a high-quality CNC aluminium housing with powerful brushless motor technology inside. This is the short shaft variant designed for AR36, AK, SG55x and AUG AEGs and is offered in 34K, 39K or 48K RPM flavours, ideal for any build objective which demands extreme speed and torque!

DARK MATTER™ motors are Brushless Motors, similar to the legendary Warhead Industries examples and boasting lower heat build-up, higher torque-to-weight ratio, improved reliability via reduced friction and significantly reduced operating noise when compared to conventional brushed motors. While installing a DARK MATTER™ motor in your AEG will make it a beast, the more important aspect is keeping it performing in the long term. As is always the case with super strong motors, we only recommend the Dark Matter series to those with the technical know-how to ensure their setup can handle it!

Redesigned for maximum compatibility with a wide variety of brands, the RetroArms CNC QSC Gearbox V2 is ideal for technical Airsofters working on a high-performance build which needs to last a lifetime. The set includes a Version 2 gearbox shell, carbon steel screws and a steel ball bearing spring guide and is ideally used for extremely high ROF or FPS builds. 

The shell itself is precision machined using CNC technology from the best aluminium around; 7075 T651, an ultra-hard alloy with similar strength properties to steel, boasting an ultimate tensile strength of 590 MPa compared to construction steel's 390 MPa. The quality of the machining simply cannot be overstated; every surface is flawlessly smooth and finished to perfection. 

Not content with making an absolutely beautiful gearbox from the finest materials around, the team at RetroArms has also put a lot of thought into the design aspect, improving on the original Tokyo Marui V2 gearbox in several areas. The piston tracks and selector plate rails have been redesigned for wider compatibility, the front of the gearbox is enlarged in every dimension to improve strength, "glue pockets" have been added around each bearing hole so they can be glued in and wider internal wiring routes for heavy gauge wiring, along with much, much more. If you're the techy type seeking a slick gearbox shell to start your build, the RetroArms CNC QSC Gearbox V2 is exactly that!

Increasing the rate of fire on your airsoft rifle sometimes causes it to misfeed, resulting in dry firing in builds with a very high rate of fire. A sector gear delay will solve your feeding problems 99.9% of the time with a simple add-on.

This sector gear clip increases the time it takes for the air nozzle to cycle. Delaying the cycle improves BB feeding by allowing the air nozzle to be retracted from the hop-feed for a longer duration.

This tiny add-on could instantly transform your AEG if it has been suffering from high rate of fire issues.

Although this is designed to be a perfect fit, it is recommended that this be permanently fixed in place using superglue, after testing to prevent it from potentially loosening over time.

A heat-shrink kit designed to give you all the heat-shrink you'll need when working on a project gun or replacing wires. The heat-shrink is constructed from PVC, and shrinks in size when heated, designed to protect wires and other electrical components.

if you're looking for a replacement Motor Cage for your TM-spec Thomspon AEG, you've just found one! The CYMA Motor Cage for CM.033/051 Thompson AEGs is a replacement original part from the CM.033/051 series and should fit most Thompson and Aliens M41A Pulse Rifle AEGs on the market, assuming they are Tokyo Marui spec internally. The set includes both sides of the motor cage but doesn't include screws so make sure you have these ready for installation. 

If you need a new cylinder head to fix up your Dragunov, check this out! The CYMA Aluminium Cylinder Head for CYMA/Real Sword SVD/SVU is constructed from CNC machined aluminium and is fitted with two O-rings to seal any gaps between it and the cylinder for perfect efficiency and minimal air loss. 

The cylinder head also has a sound dampening pad installed on the rear face which reduces gearbox noise and protects the piston head from the force of repeated impacts. A replacement original part for the CYMA CM.057 SVD/SVU series, this cylinder head is also compatible with the old Real Sword Dragunov SVD!