Airsoft Boneyard

These CYMA/EMG CM.102 SGR-12 Tri-Shot Shotguns found their way to the Boneyard due to generally poor quality control. These are brand new guns, unused and never shot but we can make no guarantees of proper functionality. As with all Boneyard items, these do not have a warranty and are sold as spare parts, wall hangers or props.

For a detailed product description and more specifications, click HERE to view the original product.

We're unsure why this platform was returned to us. During testing, its ETU was initially in set-up mode, which we can only assume a fault with it may be in play, or the gearbox has at one point been opened up for a potential attempted repair. The gun is fully functional, and whilst going through our chronograph gave us results of 330 FPS with 0.20g BBs. With minimal to no faults obvious, this platform is ready to skirmish when you are!

This SMG is fully functional, just the stock has broken apart. All original parts (as far as we know) are still present, so it'd just require understanding of how it goes back together. There is some damage to the position slots, but other than that, this replica is pretty clean!

Note that the included magazines have been previously reported to commonly run into feeding issues due to their dual feed system. You may not experience this, but it's something to consider as possible later down the line.

This EU-Series Pistol has a broken valve knocker reset. Due to this, the replica will go into full auto depending on how long the trigger is held for. Given this, the replica cannot be skirmished due to consistency issues in its current state. We're deeming this replica non-functional as it is, and recommend the knocker is replaced immediately.

This shotgun was returned to us with a pump arm that tends to "jam up". We did not experience this issue in our testing, though we cannot guarantee it won't re-emerge in the future. Shells also apparently don't feed well into this replica, which does seem to be the case. When firing, we had around 2 BBs shoot and then 3-4 roll out of the inner barrel afterwards. The final issue discovered is the mock bolt cover is broken and will freely move by itself. It will still travel when you pump the action though.

This funky pistol is sadly non-functional. There are numerous internal issues that we were unable to identify specifically. When the slide is pulled back, it sometimes gets stuck, and the slide release is non-functional. Then, when the slide is back in position, it doesn't actually set the trigger.

The pistol's furniture has also been through a lot, with scratches on some parts such as the barrel, inner barrel, and broken iron sights. The hard case that is supplied is missing a clasp that has snapped off. There is some interesting furniture on this pistol that is definitely worth using if you're into the speedy style!

From testing, this replica is non-functional. We believe that when racking the bolt, there is nothing cocking the spring, meaning you can continuously rack it but no BBs will be discharged (apart from ones stuck in the hop unit which will simply roll out). Apart from this, the rifle is in relatively decent condition so would make for a great wall hanger. It must also be noted that the magazine usually included with the replica is missing.

This replica was returned to us with a cracked receiver. The crack is located towards the end of the receiver on the right side, and is significant enough to where the barrel assembly wobbles. We advise against using the replica as the damage is likely to worsen, and the rifle may break entirely. This thing would work better as a display piece or prop for the SVD fans out there...

This replica is in the Boneyard with a snapped receiver. It is unrepairable, so is recommended to those who could benefit from having some spare SVD parts...

This replica has found its way into our boneyard due to a manufacturing issue with the front sight - it appears that it's been attached at an angle towards the right so the sights don't lineup whatsoever. Aside from this, the replica was fully functional in our testing, firing at a consistent 250 FPS on 0.20g BBs (this applies to both tri and single shot via manually loading BBs into the replica).

Ultimately this replica could be perfect if you're after a cheap shotgun and aren't too bothered about the cosmetics as you could throw on a top rail of some sort and put a red dot on the rail.

This shotgun doesn't rack or feed, and therefore doesn't fire. This could potentially be fixed by those of you with some technical knowledge but for now, it is being sold as non-functional. Cosmetically, the shotgun is in fantastic condition with little to no marks or scratches to be seen, so it could make for a fantastic prop or display piece.

This shotgun's action is jammed up - when you are able to free this, regardless of what you do you cannot cock the spring to fire the replica. The feed ramp release linkage is also broken, so you cannot access the chamber of the replica in order to load a shell. Ultimately, this replica may be better suited as a wall hanger / display piece.

This replica has found its way into our boneyard due to an issue with its bolt - it appears it jams after a short amount of travel, resulting in the replica not being functional as it cannot cock the spring properly. This replica's two-tone paint is quite worn, but still counts so this could be a decent project sniper even if you don't have UKARA!

This replica has found its way into the boneyard for unknown faults - when visually inspecting the replica, we couldn't identify any obvious faults apart from rattling inside the rear of the stock, most likely from a BB somehow finding its way and getting stuck inside there. Whilst cocking the replica, the bolt does sound like it's grinding against something however it isn't completely obstructing functionality which when firing through the chronograph, we were seeing 387 FPS +/- 10% on .2 BB's so there may be a minor airseal issue considering this replica usually fires around 415 FPS on .2 BB's.

This replica has found its way into our boneyard due to being an ex-display; externally the replica is mint and was primarily used as an example for two-tone products. When testing, we did see an issue regarding the FPS where on the chronograph it was giving us 360 FPS +/- 10% on .2 BBs indicating that there may be an airseal issue as normally this replica would fire at 415 FPS on .2 BBs so to unleash the full potential of this replica, this would need to be rectified. Other than this, you're pretty much getting a new replica.

This sniper is in the boneyard due to issues with magazine retention. In order for this sniper to feed the magazine, it needs to be held in the magazine well, this issue would need to be resolved in order to comfortably skirmish with it. Other than that, the platform looks nearly brand new, other than its blue paint job, but that just means you don't need a UKARA to purchase it!

This sniper rifle has landed in the boneyard, as there is some chipped paint from where it has been put together. This means that it should still be functional, other than the cosmetic wear. It comes with three magazines and a speedloader, so if you have the BBs ready, you can get straight to test-firing this sniper rifle!

This sniper rifle is in the boneyard due to issues with the trigger box, there are also random loose small parts in the box. The sniper seems to rack and fire, although we did not test it with BBs. It definitely needs some attention and TLC, but this sniper could be back up and running in no time if you can figure out what the specific issues are!

It also comes with a two-tone blue finish, meaning you don't need a UKARA or any defence to purchase this!

This sniper has landed in the boneyard as it has bolt issues; the bolt can be pulled back, but it does not lock, and therefore, the rifle cannot be armed. If you know how to fix this potentially easy issue, you could be onto a winner here, as it seems that this is the main issue with the sniper rifle.

It's also two-tone green blue, so you won't need a UKARA to purchase this L96!

This replica has a leaky mag, most likely due to the knocker valve that has dried o-rings and may just need some lubrication or worst case scenario, the o-ring is damaged and will need to be replaced. Ultimately this could be an easy fix however there may be other issues present as we're unable to properly test the replica itself. Its slide is currently jammed, so disassembly/assembly may be quite difficult.

This replica has found its way into our boneyard for unknown reasons - when we tested this replica, we didn't notice any obvious faults apart from a loose cocking handle whilst it's in the home position alongside pulling the bolt back. Firing the replica also presented with no clear faults where we were seeing an average of 497 FPS +/- 10% on .2 BB's although we did get a single reading that was over 500 FPS.

This replica is in the Boneyard as it doesn't work for unknown reasons. We have attempted to test it with several different batteries, but it just doesn't fire. This could be a good husk to pillage remaining functional parts from, or a prop for those wanting a MAC-10 in their collection.

This SMG has landed in the boneyard due to the front end missing, issues with the battery it came with and feeding issues. The battery has since been removed, and this gun has not been tested, so it is unclear if the platform is functional or not. The front cap that retains the battery is also missing, so a new one would need to be sourced for testing. This platform would be great for spare parts or making an excellent display piece. With its red paint job, this also means that you do not need a UKARA to purchase it!

This replica is in the Boneyard as it doesn't work for unknown reasons. Something we have been able to identify however is its damaged stock, which does not lock into any positions. We have attempted to test the platform with several different batteries, but it simply won't fire. This could be a good husk to pillage remaining functional parts from or a prop for those wanting to add a MAC-10 in their collection.

This replica has found its way into our boneyard due to an issue regarding slam firing - whilst testing, the trigger is extremely stiff suggesting that a part is most likely broken within the trigger group though we're not sure what exactly it is without disassembling the unit. Ultimately, this replica would serve better as a wall hanger which given it's also a two-tone, you won't need UKARA in order to obtain this replica!

This uniquely coloured sniper rifle has landed in the boneyard due to the cylinder screw being over tightened and damaginge the cylinder itself, this has left it non-functional and a new cylinder would need to be sourced. This could potentially be an easy fix if you're the techy type, however, there may be other issues that were missed. Due to the stylish orange paint job, you will not need a UKARA to purchase this. If you want a sniper with a potentially easy fix, or you're interested in the cool orange body, this is a great bargain to get!

This uniquely coloured sniper rifle has landed in the boneyard due to damaged/broken sears and a missing magazine. This could potentially be an easy fix if you're the techy type, however, there may be other issues that were missed. Due to the stylish orange paint job, you will not need a UKARA to purchase this. If you want a sniper with a potentially easy fix, or you're interested in the cool orange body, this is a great bargain to get!

This M50A landed in the Boneyard due to "slam firing", meaning when the bolt is pulled back it immediately snaps forward and shoots the platform. This may be a piston or sear issue but other faults may also be present.

Everything appears to be present in the box and in good condition with the exception of a minor scratch on the bolt handle, though there is a chance small parts may be missing. If you need a parts donor or a fixer-upper, this Boneyard should suit!

This replica is being sold as a Boneyard due to it double feeding, sometimes even triple feeding. This could potentially be fixed by those of you with some technical knowledge but for now it is being sold as dysfunctional. A grub screw is also missing that would hold the handguard in place, as a result, it is loose.

Cosmetically the gun shows minor scratches on the barrel, but for the most part the rifle is in great condition! It must be noted that the magazine originally provided with this replica is missing, so a replacement or two will need sourcing if you intend to get this thing back up and running again.

Manually feeding the replica, we were seeing around a 505 FPS average using 0.20g BBs, so even if you were to source a magazine and fix the feeding issue, you'll need to downgrade the spring in the platform in order to use it at a skirmish.

This replica is being sold as a Boneyard due to feeding issues, cosmetic wear, a wobbly barrel and missing magazine. Although that sounds like a lot, we're certain that some are potentially easy fixes. The cosmetic wear is present on the receiver and the feeding issues are causing multiple BBs to be fed simultaneously into the platform. Other than these issues, the gun works. This a great bargain for someone who loves the Russian aesthetic, or is looking to get a great discounted rifle with some potentially easy fixes.