All Airsoft Batteries

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too, and is designed to give you a high output for fast rate of fire and trigger response for roughly half a day dependent on trigger happiness.

If you need slim 7.4V crane stock LiPo for your crane stock or handguard battery compartment, the VP Racing 7.4V 1000mAh 20c LiPo Crane Stock Battery should do the trick. This 7.4V 2S LiPo stick battery is fitted with a Deans battery connector and is comprised of 2 cells, each of which measures 11 x 1.5 x 0.5 cm. The wire length between the cells and connector is approximately 10cm, giving you a bit of flexibility to ensure the battery is installed properly. As always, we recommend measuring thoroughly to ensure it fits before ordering!

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too. Fitted with a deans connector for low resistance.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards  and comes fitted with Deans connectors instead of the standard Tamiya for upgraded Airsoft Guns.

A super thin triple crane stock 11.1v 1300mAh 25C LiPo, which features a Deans Connector instead of the standard Mini Tamiya. 

A triple crane stock 11.1v 1450mAh 25C LiPo, which features a Deans connector instead of the standard small Tamiya.

A high output VP Racing 11.1v 1450mAh LiPo battery, designed to deliver some serious rate of fire and trigger response with the right setup.

A compact LiPo battery designed for crane stock use but also suitable for compact Airsoft hand guards too. 

An absolutely massive 11.1v LiPo 2600mAh 20c LiPo Battery in a Crane Stock configuration, with three cells which have individual dimensions of: 13.1cm x 1.98cm x 1.13cm. It has a 9cm cable with a Deans Connector on the end.

If you need a battery for your M4/AR-15 AEG Crane stock and would rather get everything you need in one place, here it is! This bundle includes a NUPROL LiPo Balance Charger, a Safe Charging Bag and a 7.4V 1450mAh LiPo Battery in Crane configuration with a Deans connector; an ideal setup for a Deans equipped rear wired M4/AR-15 AEG with a Crane stock battery compartment. 

The dimensions of the included battery are as follows: 11.4cm x 0.7cm x 1.5cm per cell group (2 cell groups on each battery) with approximately 9cm of wiring between the battery and connector. 

If you need a compact Airsoft battery which fits almost anywhere the 7.4v 1100mAh 20C LiPo Crane Battery from VAPEX is ideal. This battery is pre-wired with a mini-Tamiya battery connector and each cell unit measures 11 x 0.7 x 2.2 cm with approximately 9 cm of wiring between each cell and the connector, making it great for tight spaces and use with multiple different platforms.

The compact size of this crane/nunchuck battery makes it ideal not only for Airsoft but also for electronics hobby applications and R/C when a lightweight and compact power source is a priority. Whether it needs to fit into a buffer tube, crane stock, handguard or practically anywhere else this super slim battery is perfect, especially if you want a single battery which fits in multiple guns!

If you are looking for a decently sized crane stock battery which should last all day, the VAPEX 7.4v 2200mAh 20C LiPo Crane Battery should do the trick! This battery is a 7.4V 2S LiPo in crane/nunchuck configuration, meaning the cells are separated into two individual units which makes the battery far easier to fit into unconventionally shaped battery compartments. The pre-wired connector is the common mini-Tamiya connector and the continuous discharge rate is 20C.

Each of the individual cell units measures 11x2.2x1.2cm approximately with a wire length of 9cm between each cell and the connector, meaning this should fit nicely in most crane stocks and many handguards and full-stock battery compartments, though as always, we advise measuring carefully before ordering!

A super thin triple crane stock 11.1v 1300mAh 25C LiPo that features a standard Tamiya connector and is made up of three individual thin cells, making it great for squeezing into awkward spaces.

Proven in battle, everyone has use for Ni-Mh crane stock batteries! The advantage of NiMh batteries over their LiPo batteries is that they are less volatile and don't require balance so you can use any charger as long as it's NiMh compatible, just make sure to not leave the battery charging unattended.

This battery has a voltage of 9.6v and a capacity of 1600mAh and is comprised of 8 cells working in unison, connected via the Deans/T-Plug connector.

This Ni-Mh sports a crane configuration, one of the most common types and is perfect for split battery compartments, most often seen in M4 stocks, M16, SMG-5 and AKs with full stocks. The battery measures 12x1.8x1.8cm per 4x cells and has a wire length of roughly 8cm.

This Airsoft Battery and Charger pack features a NUPROL 9.6v 1600mAh Ni-Mh Crane Battery, NUPROL NPC-01 NiMh Battery Charger, and Safe Charging Bag which are perfectly matched to work with each other, a great choice for anyone new to Airsoft and looking for a battery for their gun. 

If your Airsoft gun comes with a sample 9.6v Block or Crane style battery and charger then this is one of the first things you should buy. The battery will last longer, charge better, and will be of much higher quality than the free gift battery included for testing in some Airsoft gun boxes!

A replacement battery for Tokyo Marui SOPMOD 6mm BB guns which use the Unique Fixed Crane Stock Style Battery Design. 

An Airsoft Gun Battery designed and built by NUPROL specifically for Airsoft Skirmishers and are part of their POWER range of Batteries.

If you're running an upgraded or MOSFET-equipped AEG, this Gens Ace 11.1v 25C 1500mAh LiPo Battery may be just what you need to power it. This Lithium Polymer (LiPo) battery is pre-wired to a Deans/T-Plug battery connector and consists of 3 cell groups wired in nun-chuck/crane/butterfly configuration. The wire length between the cells and connector is approximately 8cm and each of the 3 cells measures approximately 0.8 x 1.6 x 13 cm. 

Not all Airsoft AEGs are capable of running an 11.1V LiPo without causing damage, if you are unsure check the recommended battery section of the your gun's product description. LiPo batteries require balance charging, meaning this battery MUST be charged using a LiPo balance charger with the balance port connected. We recommend using a battery charging bag for storage and charging, and to never leave an Airsoft battery on charge while unattended.