G&G Armament ETU 2.0, MOSFET 3.0 & Vertical Trigger

G&G Armament
Code: GG-11-137-1
2,569.00 Kč
  • Programmable Trigger
  • 'Speed Trigger' Included
  • For Version 2 Rear Wired

A drop-in trigger, ETU & MOSFET for Version 2 compatible rear-wired Airsoft replicas, which includes features like a programmable trigger, low battery cutoff, shot sensor and comes included with a vertical 'speed trigger'.

Full description

Help
Size guide

Description

This is a complete and ready to install Electronic Trigger Unit for Rear Wired Version 2 Airsoft gearboxes, and is the beating heart of what makes G&G ETU products so unbeatable on out-of-the-box performance. The package includes an Electronic Trigger Unit, which is a computer controlled trigger that allows you to program three round burst in a matter of seconds. This smart trigger unit also has a shot sensor which can detect a complete gear cycle, leading to more precise single shot and longevity of components. Also included in the package is a MOSFET which protects the eletrical components of your RIF and can detect a low voltage battery - cutting it off and stopping you from fully discharging a battery or ending up in a bad situation where your battery dies with a BB in the chamber and you are unable to remove it. The MOSFET also has a blade fuse wired in series with it. This kit comes included with a flat 'speed trigger' to finish off your ETU install, and to help you get the most benefits from your new trigger with a tighter response, and less pull required to get a shot off. This is the perfect kit for replacing a dead trigger unit in any G&G weapon, or for giving your old RIF a performance boost to bring it up to a modern spec.

Features:

  • Known to be compatible with the following manufacturers:
    • Tokyo Marui
    • CYMA
    • JG
    • G&G
    • G&P
    • VFC
    • SRC (Requires slight modification to gearbox pin that locates and seats the trigger unit)
    • Classic Army (APEX series may require light dremeling on inside of gearbox casing)
  • 3 round burst option
  • Hold trigger in 'Auto' for ten seconds to change between Auto/Burst
  • Easy programming
  • Heat shrink protected electronics
  • Includes all parts required
  • Shot completion - Returns your piston to the front of the gearbox after every shot
  • Suitable for V2 gearboxes with up to 8mm sized bearings or bushings
  • Tools not included

Package Includes:

  • Electronic Trigger Unit (ETU) & fitting screw
  • Selector plate & spring
  • MOSFET with fuse
  • Motor wiring
  • Signal wiring

Special Instructions:

Please note this unit best functions with an 11v LiPo battery. This installation is not recommended for a beginner Airsofter with limited internal parts knowledge. An 11v LiPo battery will cause strain and wear to other components considerably faster than using a 7.4 LiPo or 9.6v NiMh battery. 

When installing please be extra careful when fitting the wiring, there is very little space for error. If you have 9mm bushings and bearings you may have to modify the provided selector plate. Please ensure your magazine and hop unit are empty of BBs before setting up 3-round burst or full auto cycle mode.

Due to the low voltage from different battery and/or motor specifications, it might cause an auto-semi problem. Please ensure you charge your batteries fully before use.

Specification

General

Parts & Accessories Type
Internal Parts
Internal Part Type
MOSFET, Trigger, Wiring,

Construction

Colour Wheel Greyscale
 Item Colour
Black, Red,
Construction Icon
 Construction
Alloy, Polymer, Silicon
Internal Part Construction
Polymer, Alloy, Silicon,

Part Specific

Part for Power Source Type
Electric
Weapon Platform
AR
Package Includes
  • Wiring
  • Speed Trigger
  • Electronic Trigger Unit
  • MOSFET

Electric Part Specific

Gearbox Icon
 Gearbox Version
V2 Gearbox
Gearbox Version Compatibility Variant
Version 2

Size guide

Parts Fitting

Upgrades and Downgrades should only be undertaken by experienced players, or Airsoft Technicians. Please note, changing any internal parts of a weapon voids its warranty unless done in-house by our staff. 

Please ensure that when fitting parts the part purchased is the correct part, as once a part has been fitted we cannot accept return.

We do know that players love to tinker, so we're here to give you help should you require it, and if needed you can get in touch with our workshop for more help!

Unique Parts

Please note that some parts may be unique to a specific brand of weapon. For example: Parts for an ASG M4A1 may not fit an ICS M4A1.

Parts from the same brand typically have a high chance of fitting, though be warned, some replicas use unique parts, so please ensure the part will fit before you attempt to fit it.

If you require help with fitting any parts feel free to get in touch with us via our Contact Us Page.