Airsoft Boneyard

This beautiful replica has found its way into our boneyard due to an issue regarding the trigger - as far as we can see, the trigger doesn't interface with anything which means a component is missing (further investigation is required to determine exactly what part this is).

Handling this replica also presents us with another potential issue where the slide is quite wobbly compared to normal so this would also have to be investigated. The magazine is also missing, so if you intend to repair this, then a replacement would need to be sourced; otherwise, this would be perfect as a wall hanger.

This iconic replica isn't held together properly, and a lot of its parts have been taken off/out and bagged together in the box. The platform was functional during a dry-fire test, so we can confirm that it cycles - however there may be faults that we weren't able to identify related to range or accuracy. Realistically the gun needs to be fully assembled in order to evaluate its performance.

We cannot determine what's missing from a glance; the hop unit and inner barrel assembly (including the hop rubber) are present, though the stock is nowhere to be seen. There are quite a few random parts in the bag (a lot of screws too). Ultimately this could be a relatively easy rebuild/project, though given the looming possibility that some parts may be missing, rebuilding it to its former glory could turn into a wild endeavour.

This LT-03 found its way to the Boneyard with unknown faults and has not been tested for obvious reasons. The upper and lower receivers, front end and pistol grip are present but may be missing small parts. The gearbox, motor and HOP-up unit/inner barrel are also accounted for, but we cannot guarantee functionality of these parts.

The spring guide and spring are definately missing, as is the butt plate and battery plug for the Crane stock but there may be other small parts absent which we haven't been able to identify. If you're after a cheap fixer-upper to test your tech skills or learn how to tune a gearbox, this is the Boneyard for you!

This sniper rifle has landed in the boneyard as it was non-functional from the manufacturer. It has piston/bolt issues that cause it to be non-functional. Once these have been repaired, you may have yourself a nearly brand-new platform ready for the battlefield. The box includes all its original contents.

This sniper rifle smashes BBs when they are loaded into the rifle. It has been taken apart, and it is unclear what is causing this issue. The external quality of this rifle is nearly pristine, so it could make for a great wall hanger, or if you can figure out the BB smashing issue, then you have yourself a brand new platform!

This AR36 is in the boneyard for obvious reasons, there is only half of it remaining. It is a great choice if you're looking for some replacement furniture, and it includes a magazine and foregrip. Overall, this could make a great start for fitting your own internals and with the red paint job, you don't need a UKARA to purchase it!

This replica has landed in our boneyard due to it slam firing - this could be due to the piston or sear not engaging properly with other components. The replica does show some signs of use, such as the mud splatter seen across the entire thing, though if you're happy to wipe that off you've got a UKARA compliant Two-Tone paint job, meaning a defence will not be required upon purchase.

This replica has landed in our boneyard due to the trigger assembly being bent to the point where the sear isn't able to lock onto the piston which results in the replica slam firing. This is the only fault that we're aware of, though we recommend doing a thorough investigation regarding the slam firing to figure out what needs fixing/replacing.

Other than this, the bipod originally provided with the platform is missing, so a replacement will need to be sourced if you want the full setup. Externally the replica is in decent condition and comes two-toned, meaning a UKARA or other defence will not be required upon purchase. One last thing to note is that the safety lever has snapped but still seems functional.

This replica's holding pin that allows the bolt to cock the spring has gone missing, which in turn means that a replacement will need to be sourced to get it back up and running again. Externally the platform is in good condition, although it's missing the bipod originally provided, so a replacement/alternative will need sourcing if you want the full setup.

This replica is in the Boneyard missing several body screws, this replica also needs a bit of internal work as the bolt simply slides out when racking is attempted due to missing trigger parts. Further investigation will need to be conducted to determine which parts specifically will need sourcing. Other than this, the replica is in decent condition externally so if a trigger was to be sourced, it could pass as a wall hanger. Alternatively, the platform may serve well as a husk to pillage remaining parts and furniture from.

This replica slam fires; this could be for a variety of reasons but most likely related to the sear, though we recommend further investigation into the issue for better understanding. As well as this, the bolt is rather wobbly when racked, and the safety lever has snapped, though seems to still be functional.

Ultimately this will be quite a bit of work to get fixed up, and may suit better as a parts donor instead if you're having issues with a pre-existing Specna sniper. Unfortunately the scope, bipod and magazines originally provided with this platform are all missing, so replacements will need sourcing if you intend on repairing this thing for skirmish use.

This replica is in the Boneyard missing the majority of its internal trigger components, rendering it non-functional until parts are replaced. We're unsure specifically what's missing but the platform will not rack, so it may serve best as a parts donor or an awesome display piece/prop given its pristine external condition.

This replica has landed in our boneyard due to an issue with part of the frame that secures the receiver together. Although this piece looks like it's meant to separate, there is clear indication that one of its supports has snapped, allowing for it to fall out of the frame meaning you probably won't have the most robust mounting of the receiver when putting the replica together. 

Aside from this, the platform was fully functional in our testing and fired at a 430 FPS average on 0.20g BBs. The scope, bipod and one of the magazines are unfortunately missing, so replacements will need to be sourced if you want the full setup. The replica will also need a little TLC as there's some sort of adhesive residue on the end of the outer barrel and mud at the rear of the stock.

This replica is in the Boneyard due to an issue with the action that seems to be interfering with the spring. During inspection, we have determined that the root of the cause is the spring guide coming apart and getting lodged between the trigger and piston which seems to have jammed the bolt. This is all due to the spring guide having stripped threads meaning the base and rod aren't secured.

With the shots that we could fire, we were seeing a 470 FPS average on 0.20g BBs. The replica is also missing its bipod and two of its three magazines so replacements will need to be sourced if you want the full original setup. There is also some wear on the two-tone paint.

This VMP-1C has a snapped auto sear. The sear can be manually reset in order to shoot, however, when the bolt cycles it does not engage/reset, meaning it will need replacing. The outer barrel also has stripped threads so a replacement will need to be sourced if you wish to attach a muzzle device.

This is an ideal project for someone with prior experience with this specific platform. It must also be noted that the magazine originally provided is missing, so a replacement will need to be sourced.

This sniper is in the boneyard due to issues with its cylinder; a new one would need to be sourced to repair it. There may also be other missing parts that have not been recorded. Other than these issues, the sniper rifle looks nearly brand new, if you fancy a clean body for cheap, this is a great one for you!

This CM.702A-U landed in the Boneyard with a damaged cylinder, missing HOP-up adjustment screw and torn HOP-up rubber but is near mint externally. The piston, spring and spring guide have been removed but are present in the box, as is the thread adapter and magazine.

On the outside, this Boneyard is in great condition, with a small amount of finish wear on the magazine well and Harris lug, along with a deep but small scratch on the tip of the outer barrel. Whether you need parts for your M24 build or are seeking a summer project, this Boneyard has loads of potential!

This replica has found its way into our boneyard due to various issues; the main fault is that the trigger assembly is loose and the retaining pin is nowhere to be seen - there's also some parts in the box that is most likely associated with the trigger/mcok bolt that will need reassembly if your intention is to skirmish. Due to the external quality however, this would also work as some sort of prop/wall hanger as the replica is in good condition with limited/no marks or scratches.

It's unknown why this replica was initially sent to the Boneyard, however after some investigative work, we discovered it non-functional with what seems to be either motor and/or wiring issues. Trying to shoot the replica results in the EBB seizing and no shot fired, trying to then fire again results in nothing. If you attempt to consistently fire the replica, the wiring begins to heat up quite significantly. Due to the dangerous nature of this potential fire risk, we suggest only taking this project onboard if you're an experienced tech. Adding on, there is a also some slight wear visible on the Two-Tone paint, and the charging handle for the mock bolt has snapped off.

Overall, this replica may serve best as a husk to pull spare parts and furniture from for your other broken one!

This replica's pistol grip and motor are separated from its body and the buffer tube is also rather loose, looking as though it has been damaged in some fashion. It also appears that the internal wiring and MOSFET have been removed, meaning you'll need to be a decent electronic tinkerer to get this platform back in working order. This platform is missing its fire selectors too (they are ambidextrous, so we recommend sourcing original parts for the best fitment and compatibility).

Due to the listed issues, we're unable to test for further faults and performance status. Ultimately this could make for a decent project as it's quite a nice base gun and in decent external condition.

This M870 ended up in the Boneyard due to the stock rod pulling out of the receiver. It is also missing its gas reservoir and potentially other parts/screws from inside the stock. The furniture itself appears to be in good condition, as does the shotgun itself, but the threaded rod to which the stock mounts is damaged to the extent that it will no longer tighten. The threaded socket on the rear of the shotgun is also damaged.

If you're handy with a hot glue gun, this would make a fantastic wall hanger but could also be a good source of parts if you have a Golden Eagle M870 in need of repair!

This sniper rifle has landed in our boneyard non-functional - likely caused by sear damage, though we cannot confirm without deeper investigation as there may be other faults present. The rifle does come in a two-tone red finish, meaning that you will not need a UKARA to purchase it. If you fancy a fixer-upper or like this rifle's cool, unique style, this may be the one for you!

This gas powered FABARM shotgun has a jammed pump. We're unsure on the root cause or any potential fixes to this issue, but you unfortunately won't be able to rack it. A unique platform, this one will be well worth your time to fix up, or could serve well as a display piece/prop.

This gas powered FABARM shotgun has a jammed pump. We're unsure on the root cause or any potential fixes to this issue, but you unfortunately won't be able to rack it. A unique platform, this one will be well worth your time to fix up, or could serve well as a display piece/prop.

This gas powered FABARM shotgun is in the Boneyard with several problems. It has supposedly been used for parts, though we're unsure what exactly is now missing. Its pump tends to jam when racked and the trigger does nothing. The shell tube towards the front of the platform is also broken - the threaded section for the cap is no longer secured into the tube. There may be more ongoing problems but we cannot diagnose these due to the platform not being in a functional enough condition to test. Overall this might be quite a big task to fix up, so may be better used to take more parts from, or just to serve as a pretty cool wall hanger!

This replica has found its way into our boneyard due to the pump action being jammed - we're not sure how this has occurred though investigation is required to get this beautiful replica back in action. We've also discovered that the fill valve isn't present and is nowhere to be seen so a replacement would have to be sourced. Externally the replica is in mint condition and all of the original accessories are present so if you know a fix for the pump arm, this could be a cheap deal for practically a new replica.

This replica has found its way into our boneyard due to the pump action being jammed - we're not sure how this has occurred though investigation is required to get this beautiful replica back in action. Externally the replica is in mint condition apart from a scratch on the mock bolt - all of the original accessories are present however there is a bag with a part that we can't identify also contained in the replica's box so investigation into what this could be may be necessary to fully re-assemble the replica and get it back into working order.

This gas-powered FABARM shotgun has a jammed pump; the potential cause of which could be a snapped cocking arm sear. We're unsure on any other issues or potential fixes for the identified fault, but you unfortunately won't be able to rack it. It also shows slight external wear, most noticeably on the tip of the outer barrel. A unique platform for sure, this one will be well worth your time to fix up, or could serve well as a display piece/prop.

This shotgun is jammed with BBs and will not rack; please ensure that you wear eye protection before attempting to diagnose and remedy this shotgun. It may be an easy fix after disassembling the platform, but the correct safety equipment must be used as it is unclear whether the shotgun will cycle and discharge by itself. If you like the FABARM style and fancy a cool-looking shotty at a discounted price, this could be a nice choice for you. Just remember to take extra safety precautions when attempting any work on this platform!

This shotgun is jammed with BBs. It will not rack; please ensure that you wear eye protection before attempting to diagnose and remedy this shotgun. It may be an easy fix after disassembling the platform, but the correct safety equipment must be used as it is unclear whether the shotgun will cycle and discharge by itself. The reported issue is a broken sear, so this thing may be repairable as long as you can source parts.

Externally, this STF-12 is almost immaculate, with some minor marks on the fill valve but no other damage to note. If you like the Fabarms style and fancy a cool-looking shotgun, this could be a great choice for you. Just remember to be safe while attempting any work on this platform!