Airsoft Boneyard

This replica is in the Boneyard missing the majority of its internal trigger components, rendering it non-functional until parts are replaced. We're unsure specifically what's missing but the platform will not rack, so it may serve best as a parts donor or an awesome display piece/prop given its pristine external condition.

This replica has landed in our boneyard due to it slam firing - this could be due to the piston or sear not engaging properly with other components. The replica does show some signs of use, such as the mud splatter seen across the entire thing, though if you're happy to wipe that off you've got a UKARA compliant Two-Tone paint job, meaning a defence will not be required upon purchase.

This replica has landed in our boneyard due to the trigger assembly being bent to the point where the sear isn't able to lock onto the piston which results in the replica slam firing. This is the only fault that we're aware of, though we recommend doing a thorough investigation regarding the slam firing to figure out what needs fixing/replacing.

Other than this, the bipod originally provided with the platform is missing, so a replacement will need to be sourced if you want the full setup. Externally the replica is in decent condition and comes two-toned, meaning a UKARA or other defence will not be required upon purchase. One last thing to note is that the safety lever has snapped but still seems functional.

This replica has landed in our boneyard due to it slam firing - this could either be the sear or piston causing the issue so some further investigation will be required into the root of this fault. The bolt handle lock is missing, so regardless of if the handle is up or down, it'll fire when you let go. It must also be mentioned t hat the scope, bipod, and one of the three magazines originally provided with this platform are missing, so replacements will need sourcing if you're wanting a full setup.

This replica's holding pin that allows the bolt to cock the spring has gone missing, which in turn means that a replacement will need to be sourced to get it back up and running again. Externally the platform is in good condition, although it's missing the bipod originally provided, so a replacement/alternative will need sourcing if you want the full setup.

This replica is in the Boneyard missing several body screws, this replica also needs a bit of internal work as the bolt simply slides out when racking is attempted due to missing trigger parts. Further investigation will need to be conducted to determine which parts specifically will need sourcing. Other than this, the replica is in decent condition externally so if a trigger was to be sourced, it could pass as a wall hanger. Alternatively, the platform may serve well as a husk to pillage remaining parts and furniture from.

This replica has landed in our boneyard due to an issue with part of the frame that secures the receiver together. Although this piece looks like it's meant to separate, there is clear indication that one of its supports has snapped, allowing for it to fall out of the frame meaning you probably won't have the most robust mounting of the receiver when putting the replica together. 

Aside from this, the platform was fully functional in our testing and fired at a 430 FPS average on 0.20g BBs. The scope, bipod and one of the magazines are unfortunately missing, so replacements will need to be sourced if you want the full setup. The replica will also need a little TLC as there's some sort of adhesive residue on the end of the outer barrel and mud at the rear of the stock.

This replica is in the Boneyard due to an issue with the action that seems to be interfering with the spring. During inspection, we have determined that the root of the cause is the spring guide coming apart and getting lodged between the trigger and piston which seems to have jammed the bolt. This is all due to the spring guide having stripped threads meaning the base and rod aren't secured.

With the shots that we could fire, we were seeing a 470 FPS average on 0.20g BBs. The replica is also missing its bipod and two of its three magazines so replacements will need to be sourced if you want the full original setup. There is also some wear on the two-tone paint.

This replica has landed in our Boneyard with issues relating to its trigger unit. When the bolt is pulled, it's very hard to pull fully back to where you get a positive click and the bolt doesn't try to spring back into battery. Once the replica is cocked, it's very hard to push back into battery but it is possible. The replica can still fire despite this, and in our testing we were seeing an average of around 405 FPS using 0.20g BBs. This could be a neat little sniper to use if the stiffness issue is rectified, though it must be noted that the screws to secure the frame to the receiver are unfortunately missing and will need replacing.

This replica has a damaged blowback housing and some trigger issues - due to this, the slide gets stuck when racked back as the nozzle is unable to return into its home position (missing its return spring). The hammer doesn't reset either, so if the prior issues are fixed, you'll end up firing full-auto so this is another issue that will need looking into.

Ultimately this pistol would be good as a parts donor since the frame is in good condition. Note that the magazine originally provided with this replica is also missing.

This replica was originally sent to the Boneyard due to some selector issues - apparently it only fired in full auto, though in our testing it wouldn't fire at all. We're completely unsure what issues may be at play here... The pin and spring for the bolt latch on the left side of the replica are missing, so replacements may need to be sourced for these later down the line, though their absence should not affect performance or functionality in any way.

A classic M14 replica, this thing may be best served as an awesome looking prop/display piece, so won't even need any tech work. Though if you do want to get it back up and running again, prepare for the risk of opening a can of worms...

This VMP-1C has a snapped auto sear. The sear can be manually reset in order to shoot, however when the bolt cycles it does not engage/reset, meaning it will need replacing. This is an ideal project for someone with prior experience with this specific platform. It must also be noted that the magazine originally provided is missing, so a replacement will need to be sourced.

This replica is in the Boneyard missing its cylinder head. A new one will need to be sourced to get it back up and running. Due to the nature of this issue, we've been unable to test the platform, so are unaware of any further faults (if there are any).

This replica has a damaged stock plate, and the stock itself has unfortunately gone missing. A replacement plate and stock will need sourcing unless you feel like re-wiring and rocking this thing like an MP5-K... It must also be noted that the magazine originally provided with the platform is missing, so we were unable to test for performance issues and you'll need to invest in a new one if you want to get shooting. Dry-firing the replica indicates no internal issues as it sounds to be working perfectly, though we still strongly recommend taking precautions when testing/working on this replica as we cannot guarantee that it isn't dysfunctional in some way.

This replica has some misfeeding issues, though we suspect they're likely to be the magazine's fault, not the guns. The platform is however experiencing a fault with its fire-modes in which full auto will work until the trigger is let go of, where the gun will switch to shooting in semi until the selector is flicked back between the two. The replica is in relatively good condition with very few marks or scratches on its body.

The few rounds that we managed to fire through our chronograph gave us an FPS average of around 317 on 0.20g BBs, so this thing is safe to skirmish if you can get the feeding issue fixed and don't mind a buggy full-auto.

This replica shows an excessive amount of wear, has a snapped outer barrel that freely detaches, and is experiencing some feeding problems. The suppressor usually provided with this platform is missing, though some bonus magazines seem to have been thrown in the box (3 in total, though they may all be mis-feeders). If you have some technical knowledge on fixing magazines and fancy a tinker with an outer barrel, then this is perfect pick for you!

For the rounds that we did manage to fire through our chronograph, we saw an average of around 335 FPS using 0.20g BBs, so if you were to get the magazines working properly, there's not much more work that needs to be done to get this thing back in a skirmish environment!

Note that this platform sports a Two-Tone Blue colour scheme, meaning a UKARA or other defence will not be required upon purchase. This paint is however rather worn, and so too are most of the platform's externals.

It's unknown why this replica was initially sent to the Boneyard, however after some investigative work, we discovered it non-functional with what seems to be either motor and/or wiring issues. Trying to shoot the replica results in the EBB seizing and no shot fired, trying to then fire again results in nothing. If you attempt to consistently fire the replica, the wiring begins to heat up quite significantly. Due to the dangerous nature of this potential fire risk, we suggest only taking this project onboard if you're an experienced tech. Adding on, there is a also some slight wear visible on the Two-Tone paint, and the charging handle for the mock bolt has snapped off.

Overall, this replica may serve best as a husk to pull spare parts and furniture from for your other broken one!

This replica's pistol grip and motor are separated from its body and the buffer tube is also rather loose, looking as though it has been damaged in some fashion. It also appears that the internal wiring and MOSFET have been removed, meaning you'll need to be a decent electronic tinkerer to get this platform back in working order. This platform is missing its fire selectors too (they are ambidextrous, so we recommend sourcing original parts for the best fitment and compatibility).

Due to the listed issues, we're unable to test for further faults and performance status. Ultimately this could make for a decent project as it's quite a nice base gun and in decent external condition.

This replica is being sold as non-functional. It simply will not fire. The fire selector itself (the ambidextrous side) has fallen off, so a replacement will need to be sourced for this if you do manage to get the gun back up and running. The stock's buttpad seems to come off easier than it should too, so a touch of glue may be advisable there.

Overall, this gun may be better used as a source of parts, but if you're up for the task... this might just be your winter project to fix-up.

This item is being sold as a Boneyard as it is missing a tappet plate spring, and so will not fire properly. This could potentially be fixed by those of you with the necessary spare parts and technical knowledge who fancy a bit of a tinker, but for now it is being sold as non-functional. Hey, at least it it cycles, right? Externally the rifle is in fantastic condition with little to no marks or scratches to be seen, so this replica could make for an exceptional wall hanger/display piece.

This M4 AEG is in the Boneyard due to reported inaccuracy. We couldn't test it at range, so do not know the true severity or direct cause of the problem. This could be a potential quick hop fix, or a whole can of worms to be opened - the gamble is yours! Aside from the reported inaccuracy, the platform is in fantastic external condition and should be functional.

This gas powered FABARM shotgun has a jammed pump. We're unsure on the root cause or any potential fixes to this issue, but you unfortunately won't be able to rack it. A unique platform, this one will be well worth your time to fix up, or could serve well as a display piece/prop.

This gas powered FABARM shotgun has a jammed pump. We're unsure on the root cause or any potential fixes to this issue, but you unfortunately won't be able to rack it. A unique platform, this one will be well worth your time to fix up, or could serve well as a display piece/prop.

This gas powered FABARM shotgun is in the Boneyard with several problems. It has supposedly been used for parts, though we're unsure what exactly is now missing. Its pump tends to jam when racked and the trigger does nothing. The shell tube towards the front of the platform is also broken - the threaded section for the cap is no longer secured into the tube. There may be more ongoing problems but we cannot diagnose these due to the platform not being in a functional enough condition to test. Overall this might be quite a big task to fix up, so may be better used to take more parts from, or just to serve as a pretty cool wall hanger!

This GLOCK replica has excessive wear on its outer barrel. There was also a broken-off piece found in the box alongside the pistol, which upon further inspection appears to have also come from the outer barrel where the front of the hop unit sits. The front spring guide block is also missing, meaning there may be mechanism issues when firing this replica which is also somewhat indicated by the rather unsatisfying racking of the slide. This could be an easy fix-up if both of the problematic parts are replaced (spring guide block and outer barrel).

This rifle is suffering from some problems with its bolt and the cocking of it. If you pull back the bolt and return it to battery, there is no spring tension at all throughout the process, and it doesn't reset the trigger. Ultimately, it's dead. If you're a technician with some prior experience with springers, this could be a decent project for you to figure out...

This replica has landed in our Boneyard missing a whole bunch of parts. There's so many parts missing that it's easier to state what's left; the body of the replica, outer barrel, gearbox shell, hop unit, and charging handle assembly (including the guide and baseplate for the spring and cocking handle). On the side of the platform, the original selector and spring guide for the gearbox is also present.

Due to how much would need to be done in order to get it working again (it's missing basically everything inside the gearbox), this replica may ultimately serve best as a parts donor for what's remaining. Externally, what's left of the platform is surprisingly in mint condition. Not that it particularly matters in this state, but it must be noted that this replica's magazine is also missing, so a replacement or two will need sourcing if you do intend to somehow get this thing shooting again.

This replica is in the Boneyard due to its low power output. In our testing we were seeing a 185 FPS average from this thing on 0.20g BBs, suggesting that the air seal is rather poor and the o-ring found on the piston may be at fault. Some of the furniture on this platform also seems to be slightly wobbly, including the lower handguard and stock. These may need some tinkering if you're wanting a gun that doesn't rattle.

We must also mention that during our testing, a metallic smell began emitting from the gun and the wires to our battery increased significantly in temperature. There may be some kind of short happening, or the motor is being over-stressed, we're not entirely sure. One last thing to note is that the magazine provided with the replica unfortunately doesn't seem to want to lock in place properly, though when using others (in our case, a Specna Arms mid-cap J-Series magazine), no issues are found with fitting or feeding.

This Saiga-12K AEG is in the Boneyard due to having a broken stock latch. The stock can be fixed or folded, but the action between these will require a rather difficult press into what's remaining of the button toward the back of the platform. Aside from this, the gun is in pristine external condition. It unfortunately was however also shooting up to 400FPS in testing (way hotter then it should), so will need downgrading before skirmish use.

This Cowboy Rifle is missing parts relating to its gas mechanism. It seems the hammer also has an issue where it will fire at random shortly after the replica is cocked. We've also encountered some irregular extraction failures of the shells where they'll get stuck either in the chamber when they're attempted to be ejected or where they're transferred from the feed tube into the chamber.

One major benefit for this replica is that it's two-tone red, meaning you won't need UKARA or other defence if you're wanting to purchase it as a display piece or even just a cool lever-action to play around with!